Denon AVR-2802 Stereo System User Manual


  Open as PDF
of 74
 
18
ENGLISH
• If your AV component is not a DENON product or it cannot be operated with the preset memory codesets,
you can “teach” the AVR-2802’s remote control to “learn” the codes from the component’s original remote
control.
• The buttons that can be “learned” are the CD, TAPE and CDR/MD system
buttons (see page 15) and the DVD, VDP, VCR and TV system buttons (see
page 17). (For the CD, CDR/MD, DVD, VDP and TV, the A block buttons can
also be “learned”, and for the DVD and TV, the B block buttons can also be
“learned”.)
Learning function
1
Press the USE/LEARN selector button with the
tip of a pen etc., to set the learn mode. Both
the START and LEARNED/TX indicators flash.
2
Set the program switch to the side to be
learned.
Set to the AUDIO side for the CD, tape deck or
CDR/MD position, to the VIDEO side for the
DVD, VDP, VCR or TV position.
AVR/AVC VIDEO
AUDIO
3
Set the program switch to the position to be
learned.
DVD
START LEARNED/TX
SPEAKER
TUNING
BAND
TITLE
MENU/GUIDE
MODE
MEMORY
RDS
PTY
RT
USE/LEARNT.TONE MULTI DVD
SET UP
RETURN
STATUS
DISPLAY
ON SCREEN
DOLBY / DTS
SURROUND
DIRECT
DSP SIMULATION
5CH / 6CH STEREO
STEREO
INPUT MODE
ANALOG EXT.IN
MUTING
MASTER VOL.
VOLUME DISC SKIP+
SYSTEM CALL POWER
VDP TUNER SHIFT
TV/DBS PHONO
VCR-1 CD CHANNEL
VCR-2/V.AUX
TV/VCR
AVR/AVC VIDEO DVD TV
AUDIO
VDP VCR
CD
MULTI
CDR/MDTAPE
SYSTEM
SETUP
SURROUND
PARAMETER
CH SELECT
SELECT
RC-904
123
4
SET
A / B
CALL OFF
ENTER
ON
/
SOURCE
56
789
+10
0
A
2
4
3
B
1,8
CDR
/
TAPE
DVD TV
VDP VCR
CD
MULTI
CDR/MDTAPE
4
Set the remote control units so they are facing
each other, then press the button to be learned
on this unit’s remote control unit.
5
Check that the START LED is lit, then press the
button to be “learned” on the other remote
control unit.
6
Once the START LED turns off and the
LEARNED/TX LED lights, release the button on
the other remote
control unit.
7
To “learn” other buttons, repeat steps 2 to 6.
8
Once the learning operation is completed,
press the USE/LEARN selector button again.
The two LEDs stop flashing and the learning
mode is cancelled.
This unit’s remote
control unit
Flashes
The indicator stops flashing and the START LED
lights.
The learnable buttons are the buttons which can
be operated with the DENON system codes for
the CD player, tape deck, CD recorder, MD
recorder, the buttons which can be operated
with the preset memory for the DVD, VCR, VDP
and TV. For the TV only, however, the buttons in
the section indicated “A” on the diagram above
can also be “learned”. Use these to “learn” TV
channels.
This unit’s remote
control unit
Transmitting windows
Other remote
control unit
Approx.
5 cm
Light
This unit’s remote
control unit
Other remote
control unit
The two LEDs start
flashing again.
Light
Check that the stored
codes work properly.
NOTES:
• Up to 26 codes can be “learned”, but this number may be lower if the codes are long.
• If a non-learnable button is pressed or two or more buttons are pressed at once, the two LEDs will once
again light when the button(s) is released.
• If the codes could not be stored, the LEARNED/TX LED does not light after the START LED turns off. For
limited number of models, codes cannot be stored in RC-904.
• If the two LEDs start flashing rapidly after the START LED lights, this means that the memory is already full,
and the code you have just attempted to store was not stored.
To “learn” that code, first perform the resetting operation. (See page 19.)
• The included remote control unit is equipped with a system call function for transmitting multiple remote
control signals when a single button is pressed (this is often referred to as a “macro” function).
This function can be used to turn on the amplifier’s power, select the input source, turn on the monitor TV’s
power, turn on a source component’s power and start playback, etc., all at the touch of a button.
(1) System call buttons
The buttons that can be used for the system call function are shown on the table below.
A series of up to 10 operations can be performed with the POWER ON and OFF buttons, and a series of up
to 5 operations can be performed with other buttons.
System call signals are already preset at the buttons indicated in the shaded section. System call signals can
also be stored at any button on the remote control unit, including the buttons in this section. (See page 19.)
System call function
Button
No.
transmissions
Stored
operation 1
The system call signals for the POWER
OFF and POWER ON buttons are
transmitted from the remote control unit
approximately once every second.
The signals for the other buttons (DVD,
VDP, TV / DBS, VCR-1 and CD) are
transmitted approximately once every
1.5 seconds.
Stored
operation 2
Stored
operation 3
Stored
operation 4
Stored
operation 5
Stored
operation 6
Stored
operation 7
Stored
operation 8
Stored
operation 9
Stored
operation 10
POWER OFF 10
POWER ON 10
DVD 5
Receiver
power on
DVD player
(DVD)
power on
Receiver
input source
switched to
DVD
TV power on
DVD player
(DVD)
playback
VDP 5
Receiver
power on
LD player
(VDP)
power on
Receiver
input source
switched to
VDP
TV power on
LD player
(VDP)
playback
TV/DBS 5
Receiver
power on
TV power on
Receiver
input source
switched to
TV/DBS
VCR-1 5
Receiver
power on
Video (VCR)
power on
Receiver
input source
switched to
VCR-1
TV power on
Video (VCR)
playback
CD 5
Receiver
power on
Receiver
input source
switched to
CD
(2) Using the system call function
DVD
START LEARNED/TX
SPEAKER
TUNING
BAND
TITLE
MENU/GUIDE
MODE
MEMORY
RDS
PTY
RT
USE/LEARNT.TONE MULTI SET UP
RETURN
STATUS
DISPLAY
ON SCREEN
DOLBY / DTS
SURROUND
DIRECT
DSP SIMULATION
5CH / 6CH STEREO
STEREO
INPUT MODE
ANALOG EXT.IN
MUTING
MASTER VOL.
VOLUME DISC SKIP+
SYSTEM CALL POWER
VDP TUNER SHIFT
TV/DBS PHONO
VCR-1 CD CHANNEL
VCR-2/V.AUX
TV/VCR
AVR/AVC VIDEO DVD TV
AUDIO
VDP VCR
CD
MULTI
CDR/MDTAPE
SYSTEM
SETUP
SURROUND
PARAMETER
CH SELECT
SELECT
RC-904
123
4
SET
A / B
CALL OFF
ENTER
ON
/
SOURCE
56
789
+10
0
2
1
CDR
/
TAPE
1
Press the system call button.
• The LEARNED/TX LED flashes for 5
seconds.
CALL
2
Press the button at which the desired system call signals are
stored while the LEARNED/TX LED is flashing.
• The preset signals or the signals you have stored at that
button are transmitted in succession.
 previous next