Filter
Top Products
Preset codes set upon shipment from the factory.
16
ENGLISH
• DENON components can be operated by setting the preset memory for CDR or MD. Operation is not
possible for some models, however. In this case use the learning function (see page 18) to store the
remote control signals.
• For instructions on clearing the presettings stored in the preset memory, see page 19.
Preset memory (Audio component)
1
Set the slide switch to “AUDIO”.
AVR/AVC VIDEO
AUDIO
2
Set the slide switch to “CDR/MD”.
DVD TV
VDP VCR
CD
MULTI
CDR/MDTAPE
DVD
START LEARNED/TX
SPEAKER
TUNING
BAND
TITLE
MENU/GUIDE
MODE
MEMORY
RDS
PTY
RT
USE/LEARNT.TONE MULTI DVD
SET UP
RETURN
STATUS
DISPLAY
ON SCREEN
DOLBY / DTS
SURROUND
DIRECT
DSP SIMULATION
5CH / 6CH STEREO
STEREO
INPUT MODE
ANALOG EXT.IN
MUTING
MASTER VOL.
VOLUME DISC SKIP+
SYSTEM CALL POWER
VDP TUNER SHIFT
TV/DBS PHONO
VCR-1 CD CHANNEL
VCR-2/V.AUX
TV/VCR
AVR/AVC VIDEO DVD TV
AUDIO
VDP VCR
CD
MULTI
CDR/MDTAPE
SYSTEM
SETUP
SURROUND
PARAMETER
CH SELECT
SELECT
RC-904
123
4
SET
A / B
CALL OFF
ENTER
ON
/
SOURCE
56
789
+10
0
3
3
2
1
CDR
/
TAPE
3
Holding in the POWER button, press the button for the
components you want to set.
The LEARNED/TX LED flashes.
• DENON and other makes of components can be operated by setting the preset memory for your make of
video component. Operation is not possible for some models, however. In this case use the learning
function (see page 18) to store the remote control signals.
• For instructions on clearing the presettings stored in the preset memory, see page 19.
Preset memory (Video component)
1
Set the slide switch to “VIDEO”.
AVR/AVC VIDEO
AUDIO
2
Set the slide switch to the component to be
registered (DVD, VDP, VCR or TV). .
DVD TV
VDP VCR
CD
MULTI
CDR/MDTAPE
DVD
START LEARNED/TX
SPEAKER
TUNING
BAND
TITLE
MENU/GUIDE
MODE
MEMORY
RDS
PTY
RT
USE/LEARNT.TONE MULTI DVD
SET UP
RETURN
STATUS
DISPLAY
ON SCREEN
DOLBY / DTS
SURROUND
DIRECT
DSP SIMULATION
5CH / 6CH STEREO
STEREO
INPUT MODE
ANALOG EXT.IN
MUTING
MASTER VOL.
VOLUME DISC SKIP+
SYSTEM CALL POWER
VDP TUNER SHIFT
TV/DBS PHONO
VCR-1 CD CHANNEL
VCR-2/V.AUX
TV/VCR
AVR/AVC VIDEO DVD TV
AUDIO
VDP VCR
CD
MULTI
CDR/MDTAPE
SYSTEM
SETUP
SURROUND
PARAMETER
CH SELECT
SELECT
RC-904
123
4
SET
A / B
CALL OFF
ENTER
ON
/
SOURCE
56
789
+10
0
3
3,4
4
2
1
CDR
/
TAPE
4
Next, while holding the POWER button, press the button for
the code in block B. (Refer to Table 1.) The operation is
completed when the button is released and the LEARNED/TX
LED lights.
“CDR/MD”
(DIRECT) (STEREO) (EXT. IN)
DIRECT
STEREO
EXT.IN
DENON CDR A DENON CDR B DENON MD(POWER)
ON
/
SOURCE
Combinations of Personal System Codes
Keep the POWER button pressed in when
performing steps 3 and 4
()
3
Holding in the POWER button, press the button for the
corresponding manufacturer in block A. (Refer to Table 1.)
The LEARNED/TX LED flashes.
Flashes
5
To continue registering other components, repeat steps 2 to 4.
• This remote control unit can be used to operate components of
other manufacturers without using the learning function by
registering the manufacturer of the component as shown on Table 1.