Filter
Top Products
ENGLISH
32
Learning function
• If your AV component is not a DENON product or it cannot be operated with the preset memory codesets, you can “teach” the AVR-2802/982’s
remote control to “learn” the codes from the component’s original remote control.
• The buttons that can be “learned” are the CD, TAPE and CDR/MD system buttons (see page 28) and
the DVD, VDP, VCR and TV system buttons (see page 31). (For the CD, CDR/MD, DVD, VDP and TV, the
A block buttons can also be “learned”, and for the DVD and TV, the B block buttons can also be
“learned”.)
1
Press the USE/LEARN selector button with the tip of a pen
etc., to set the learn mode. Both the START and LEARNED/TX
indicators flash.
This unit’s remote
control unit
Flashes
2
Set the program switch to the side to be learned.
Set to the AUDIO side for the CD, tape deck or CDR/MD
position, to the VIDEO side for the DVD, VDP, VCR or TV
position.
AVR/AVC VIDEO
AUDIO
3
Set the program switch to the position to be learned.
4
Set the remote control units so they are facing each other,
then press the button to be learned on this unit’s remote
control unit.
The indicator stops flashing and the START LED lights.
The learnable buttons are the buttons which can be operated
with the DENON system codes for the CD player, tape deck,
CD recorder, MD recorder, the buttons which can be operated
with the preset memory for the DVD, VCR, VDP and TV. For
the TV only, however, the buttons in the section indicated “A”
on the diagram above can also be “learned”. Use these to
“learn” TV channels.
DVD TV
VDP VCR
CD
MULTI
CDR/MDTAPE
This unit’s remote
control unit
Transmitting windows
Other remote
control unit
Approx.
5 cm
DVD
START LEARNED/TX
SPEAKER
TUNING
BAND
TITLE
MENU/GUIDE
MODE
MEMORY
USE/LEARN T.TONE MULTI DVD
SET UP
RETURN
STATUS
DISPLAY
ON SCREEN
DOLBY / DTS
SURROUND
DIRECT
DSP SIMULATION
5CH / 6CH STEREO
STEREO
INPUT MODE
ANALOG EXT.IN
MUTING
MASTER VOL.
VOLUME DISC SKIP+
SYSTEM CALL POWER
VDP TUNER SHIFT
TV/DBS PHONO
VCR-1 CD CHANNEL
VCR-2/V.AUX
TV/VCR
AVR/AVC VIDEO DVD TV
AUDIO
VDP VCR
CD
MULTI
CDR/MDTAPE
SYSTEM
SETUP
SURROUND
PARAMETER
CH SELECT
SELECT
RC-903
123
4
SET
A / B
CALL OFF
ENTER
ON
/
SOURCE
56
789
+10
0
A
2
4
3
B
1,8
CDR
/
TAPE
5
Check that the START LED is lit, then press the button to be
“learned” on the other remote control unit.
6
Once the START LED turns off and the LEARNED/TX LED
lights, release the button on the other remote control unit.
7
To “learn” other buttons, repeat steps 2 to 6.
8
Once the learning operation is completed, press the
USE/LEARN selector button again.
The two LEDs stop flashing and the learning mode is
cancelled.
This unit’s remote
control unit
Other remote
control unit
The two LEDs start
flashing again.
Light
Light
NOTES:
• Up to 26 codes can be “learned”, but this number may be lower if the codes are long.
• If a non-learnable button is pressed or two or more buttons are pressed at once, the two LEDs will once again light when the button(s)
is released.
• If the codes could not be stored, the LEARNED/TX LED does not light after the START LED turns off. For limited number of models, codes
cannot be stored in RC-903.
• If the two LEDs start flashing rapidly after the START LED lights, this means that the memory is already full, and the code you have just
attempted to store was not stored.
To “learn” that code, first perform the resetting operation. (See page 35.)
Check that the stored
codes work properly.