Filter
Top Products
ENGLIS
29
Preset memory (Audio component)
• DENON components can be operated by setting the preset memory for CDR or MD. Operation is not possible for some models, however.
In this case use the learning function (see page 32) to store the remote control signals.
• For instructions on clearing the presettings stored in the preset memory, see page 35.
1
2
Set the slide switch to “AUDIO”.
Set the slide switch to “CDR/MD.
The LEARNED/TX LED flashes.
Keep the POWER button pressed in
when performing steps 3 and 4
()
AVR/AVC VIDEO
AUDIO
DVD TV
VDP VCR
CD
MULTI
CDR/MDTAPE
3
Holding in the POWER button, press the
button for the components you want to
set.
DVD
START LEARNED/TX
SPEAKER
TUNING
DOLBY / DTS
SURROUND
DIRECT
DSP SIMULATION
5CH / 6CH STEREO
STEREO
INPUT MODE
ANALOG EXT.IN
MUTING
MASTER VOL.
VOLUME DISC SKIP+
SYSTEM CALL POWER
VDP TUNER SHIFT
TV/DBS PHONO
VCR-1 CD CHANNEL
VCR-2/V.AUX
TV/VCR
AVR/AVC VIDEO DVD TV
AUDIO
VDP VCR
CD
MULTI
CDR/MDTAPE
SYSTEM
SETUP
SURROUND
PARAMETER
RC-903
123
4
SET
A / B
CALL OFF
ON
/
SOURCE
56
789
+10
0
3
3
2
1
CDR
/
TAPE
“CDR/MD”
(DIRECT) (STEREO) (EXT. IN)
DIRECT
STEREO
EXT.IN
DENON CDR A DENON CDR B DENON MD(POWER)
ON
/
SOURCE
Combinations of Personal System Codes
Preset memory (Video component)
• DENON and other makes of components can be operated by setting the preset memory for your make of video component. Operation is not
possible for some models, however. In this case use the learning function (see page 32) to store the remote control signals.
• For instructions on clearing the presettings stored in the preset memory, see page 35.
1
2
3
Set the slide switch to “VIDEO”.
Set the slide switch to the component to
be registered (DVD, VDP, VCR or TV).
Holding in the POWER button, press the
button for the corresponding manufacturer
in block A.
(Refer to Table 1.)
The LEARNED/TX LED flashes.
Keep the POWER button pressed in
when performing steps 3 and 4
()
AVR/AVC VIDEO
AUDIO
DVD TV
VDP VCR
CD
MULTI
CDR/MDTAPE
Flashes
4
5
Next, while holding the POWER button,
press the button for the code in block B.
(Refer to Table 1.) The operation is
completed when the button is released and
the LEARNED/TX LED lights.
To continue registering other components,
repeat steps 2 to 4.
DVD
START LEARNED/TX
SPEAKER
TUNING
BAND
TITLE
MENU/GUIDE
MODE
MEMORY
USE/LEARN T.TONE MULTI DVD
SET UP
RETURN
STATUS
DISPLAY
ON SCREEN
DOLBY / DTS
SURROUND
DIRECT
DSP SIMULATION
5CH / 6CH STEREO
STEREO
INPUT MODE
ANALOG EXT.IN
MUTING
MASTER VOL.
VOLUME DISC SKIP+
SYSTEM CALL POWER
VDP TUNER SHIFT
TV/DBS PHONO
VCR-1 CD CHANNEL
VCR-2/V.AUX
TV/VCR
AVR/AVC VIDEO DVD TV
AUDIO
VDP VCR
CD
MULTI
CDR/MDTAPE
SYSTEM
SETUP
SURROUND
PARAMETER
CH SELECT
SELECT
RC-903
123
4
SET
A / B
CALL OFF
ENTER
ON
/
SOURCE
56
789
+10
0
3
3,4
4
2
1
CDR
/
TAPE
• This remote control unit can be used to operate components of other manufacturers without using the learning function by registering the
manufacturer of the component as shown on Table 1.
*
Preset codes set upon shipment from the factory.