Filter
Top Products
6
Immediately turn the power off, unplug the
projector, and contact your dealer under the
following conditions, otherwise a fire or an electric
shock may result.
– If smoke comes out from it.
– If it emits a strange odor, or makes a strange
noise.
– If lamp goes out with a loud bang.
– If water or any other liquid gets into it.
– If metal or foreign objects get inside it.
– If it is knocked down or dropped and the cabinet
is broken.
Follow the instructions below when using the
power cable, otherwise a fire, an electric shock, or
injury may result.
– Do not place heavy objects on the power cord
or position the power cord under the projector.
Doing so may damage the power cord.
– Do not run the power cord under a carpet. As it
goes unnoticed, excessive load may be applied
on the cord unintentionally.
– Do not modify, bend forcibly, twist, or pull the
power cord.
– Do not place the power cord near heat
generating equipment or heat it.
– Do not bend, wind, or bind excessively the
power cord when using it.
– Be sure to connect the projector to a grounded
outlet. Failure to do so may result in an electric
shock.
– Do not continue to use a damaged power cord.
If the power cord is damaged, take it to your
dealer and have it replace.
– Use only the supplied power cord.
Follow the instructions below when handling the
power plug or connector, otherwise a fire, an
electric shock, or injury may result.
– Use the projector within the voltage range
specified on the projector (AC 100 V– 240 V).
– Insert the power plug or connector into the
power outlet firmly. Do not use a damaged or
loosen power plug or connector.
– Be sure to hold the power cord plug or
connector when disconnecting it from the power
outlet. If the power cord itself is pulled, it may be
damaged.
– Do not plug or unplug the power cord with wet
hands.
– Disconnect the power cord from the power
outlet before cleaning the projector.
– Do not stick metal objects into the electrical
contacts of the power plug or connector.
Follow the instructions below to install or handle
the projector. Otherwise, a fire, an electric shock,
or injury may result.
– Do not touch the projector, power cord, or
cables when lighting begins.
– Do not use the projector in a bathroom or
shower room.
– Do not expose the projector to rain, snow, or
use near water.
– Do not insert metal objects into the projector
through the air vents.
– Do not place the containers with water on the
projector.
– Do not install in the locations exposed to oily
vapors or smoke (e.g., near a cooking table or
humidifier).
– Before moving the projector, turn the power off
and disconnect the power cord and all cables.
– Do not put spray cans in front of the exhaust
vent. When spray cans are exposed to heat, the
pressure in them will increase and explode.
– Do not open nor remove the cabinet. There are
high voltage components inside the projector.
Contact your dealer for inspection, adjustment,
and service.
– Do not attempt to disassemble the projector
(including expendable parts) or remote
controller.
– Do not look into the lens while the projector
is used. Strong light may hurt your eyes. Be
especially careful that small children do not look
into the lens.
– When an extension cord is necessary, be sure
that the total current load of all equipment
connected to the extension cord does not
exceed the specified rating of the extension
cord.
– Periodically unplug the power cord and remove
the dust that builds up on the power cord or
connector.
Follow the instructions below when handling the
batteries. Failure to do so may cause explosion,
heat generation, a fire, or leakage of the battery
fluid.
– Do not heat or disassemble the batteries, or
throw them into fire.
– Do not attempt to recharge the batteries.
Follow the instructions below when the lamp is
replaced or breaks.
– Always unplug the power cord before replacing
the lamp.
– When the lamp breaks, shards of glass may
scatter in the lamp housing. Contact your dealer
for cleaning or inspecting the projector, or
replacing the lamp.