Filter
Top Products
8
Remote control
Picture Adjustment
Press to select various picture adjustments for sources that
have the Scaler set to Process only.
An adjustment bar will appear on the TV for the current item
(Brightness, Contracts etc.) Press the Pic. Adj. button again to
move to the next item.
Lip sync
Press to activate and adjust the lip sync delay function if the
audio and video appear out of sync. While the Lip sync delay
status is shown on the units display, use the Vol and Vol
buttons to adjust the delay time. Adjusting the value to zero
causes lip sync delay to be turned off. See later section in this
manual.
Tuner AM/FM, BD/DVD, Video 1, Video 2,
Vid 3/MP3, Tape/MD/CDR, CD/Aux/TV
Press the corresponding button to change the input source.
Pressing the Tuner AM/FM button a second time toggles
between AM and FM modes.
Pressing the CD/Aux/TV button a second time if ARC is enable
(see later section) selects TV-ARC (Audio Return Channel).
The above button descriptions are naturally brief. Please
refer to the ‘Operating Instructions’ section of this manual for
more information on the relevant functions implemented.
Apple device compatibility
The Azur 551R Navigator remote control can control the basic
functions of Apple devices such as Apple TV and Apple’s
iPod/iPhone/iPad range when docked in a Cambridge Audio
or Apple dock.
Press and hold the source button that corresponds to the
input that the Apple product is connected to whilst also
pressing one of the buttons below.
The functions are slightly different depending on the Apple
product.
Enter
Menu
Play/Pause
Used to control volume and/or navigate menus.
Used to navigate menus or Skip/Scan depending
on Apple product used.
In addition, the Azur remote can be paired with up to six
specific Apple devices using any of the six source buttons.
This can be useful if you have more than one Apple product.
For more information on pairing refer to your Apple
device’s instruction manual.
Pairing – To pair with an Apple device, press and hold the
required source button along with the button for six
seconds. Some devices like Apple TV have visual indication
once pairing is achieved.
Un-pairing – To un-pair an Apple device, press and hold any
of the source buttons along with the button for six
seconds.
The 551R is supplied with an Azur Navigator remote control.
Insert the supplied AAA batteries to use. For full details of the
various adjustment functions available from the remote, refer
to the later sections of this manual.
Standby/On
Switches the unit between Standby mode and On.
Analogue Direct
Directly selects a stereo analogue input for the current source
with no A/D conversion or DSP processing.
Stereo Modes
Selects Stereo or Stereo + Sub modes for Analogue or Digital
sources (digitally processed).
Surround Modes
Selects digital surround processing modes and various matrix
encoded surround processing modes for analogue or digital
sources (digitally processed).
Info
Press to view the current source material and decoding mode.
Press again whilst the current decoding mode is scrolling (as
long as mute is not on) to display the incoming sample rate.
When listening to FM with RDS, press to cycle round various
RDS information modes.
Stereo Mono
When listening to FM, press to alternate between stereo and
mono modes.
Store
Press to store the current frequency when in Tuner mode.
Mode
Press to select Auto/Manual or Preset tuning when in Tuner
mode.
Mute
Mutes the audio on the AV Receiver. Press again to cancel
mute.
Volume
Increase or decrease the volume of the AV receiver output.
Also used as up/down in the OSD setup menus.
Tune / Left & Right
Press the right arrow to increase tuner frequency/change
preset. Press the left arrow to decrease tuner
frequency/change preset. Also used to scroll left/right in the
OSD setup menus.
Enter
Used in the OSD setup menus.
On-Screen Display (OSD)
Press to turn on and off the on-screen setup menus for
display on your monitor/screen.
Bass/Treble
Press for bass/treble adjustment, using the Volume up/down
buttons. Note: Bass/Treble is bypassed in analogue stereo
direct and 7.1 direct modes.
Audio In Type
Switches the audio between the types available for the
current source. Depending on the source selected and
whether you have assigned an HDMI input to it, Analogue,
Digital and HDMI can be available.
7.1 Direct
Selects the 5.1/7.1 direct input.