Filter
Top Products
540R v3azur
17
ENGLISH
If no bitstream is present, pressing this button will result in the 540R v3
displaying ‘MODE UNAVAILABLE’.
Note:
The modes available for each button depend both on the Speaker
Configuration that has previously been set in the OSD and on the source
material.
For 5.1 Speaker setups the Dolby Digital/DTS Surround Modes button
will have a maximum of only one mode available which will depend on
the source material. See the following ‘Decode modes’ tables.
The Pro Logic/Neo:6/DSP modes button will present more options
where possible including Post-Processed modes.
These are modes that allow extra processing to be applied after the
main surround-sound decoding. For instance Dolby Digital (2/0) + PLII
Music. Which adds a 5.1 Pro Logic decode to a Stereo Dolby Digital
decode to turn 2 channel stereo into 5.1.
This mode would be accessed by first selecting the Dolby Digital EX /
DTS ES Mode button with a Dolby (2/0) bitstream present (selects a
normal Dolby Digital (2/0) decode. Now press the Pro Logic/ Neo:6/DSP
mode button to access the next mode which adds a PLII decode on top.
For 6.1 speaker setups, the number of decoding possibilities increases
as shown in the following ‘Decode modes’ tables. Several extra Post
Processing modes are available using Pro Logic II or IIx.
Incoming
Dolby
Digital/DTS
streams
are
always
shown
on
the
front
panel
di
splay
as
Dolby
Digital
(x/x)
or
DTS
(x/x),
where
the
bracketed
numbers
indicate
the
active
channels
in
the
source
material.
Active
output
channels
are
shown
by
the
icons
on
the
right
hand
side
of
the
front
panel
display.
Possible
incoming
DD/DTS
types
are:
(1/0) - Mono, Centre channel only
(2/0) - Left/Right stereo
(2/1) - Left/Right stereo and LFE (Sub)
(2/2) - Left/Right stereo and Left/Right surround
(3/0) - Left, Centre, Right
(3/1) - Left, Centre, Right and LFE (Sub)
(3/2) - 5.1: Left, Right, Centre, Left Surround, Right Surround and LFE
(Sub)
(3/3) - 6.1: Left, Right, Centre, Left Surround, Right Surround, Surround
Back and LFE (Sub)
Operating instructions
To activate the 540R v3, switch the Power button on the rear panel to
On then press the Standby/On button on the front panel.
Selecting the source
1. Select the desired source by pushing the corresponding source
button on the front panel or remote control.
2. If necessary, press the Input Mode button to select the input mode of
the source equipment, either analog or digital (depending on the
connection made on the rear panel).
The digital or analog icons on the display show which is the
currently selected input type.
Note:
The 540R v3 stores the input type for each source so that it is
automatically recalled when that source is selected again.
Selecting the desired listening mode
Select an appropriate mode for the source material/type you are
listening to by pressing one of the 3 main Digital Processing Options
buttons and cycling through sub-modes where available.
In
all
cases
the
first
time
a
mode
button
is
pressed
the
540R
v3
will
report
the
curr
ent
decoding
mode
on
the
front
panel
display.
Pressing
the
button
again
will
then
cycle
to
the
next
available
mode
(if
there
is
one).
If
no
button
is
pressed
for
4
or
5
seconds
the
540R
v3
returns
to
normal
operation
without
changing
mode.
Stereo
Modes
-
Selects 2 channel Stereo operation for stereo material,
pressing again selects Stereo + Sub mode.
This is a digitally processed mode that allows bass and treble controls,
and sub generation if required. The input can be either analog (in which
case it will be turned into digital by 24 bit A/D conversion) or natively
digital.
Digital inputs can be connected to the SPDIF outputs from Tuner's or CD
Players etc (LPCM) or the digital outputs of DVD players (set to
Bitstream/Raw) playing 2-channel Dolby Digital (2/0) or DTS (2/0)
material.
Pro
Logic/Neo:6/DSP
modes
-
Selects a range of surround modes with
appropriate matrix encoded material.
These modes are for use with the analog or digital outputs from TV's or
VCR Players for instance if the source material has been encoded using
one of these processes.
Pro Logic and Neo:6 are both available in various guises to decode
appropriately encoded soundtracks. Additionally DSP modes are
available to process sources with no encoding at all. Due to the matrix
encoding process none of these modes incorporate flags that tell the
540R v3 the type of encoding used in the source material. Thus you
must manually select these modes.
Dolby
Digital
EX/DTS
ES
Modes
-
Selects a range of digital surround
modes with the appropriately digitally encoded material (only). These
modes are for use with the digital outputs (set to Bitstream/Raw) from
DVD players or satellite receivers etc. In order for the 540R v3 to allow
selection of these modes a valid input digital bitstream must be present.
This is because the 540R v3 needs to read the incoming flags in order
to determine the type of decoding which can be used and present any
options that might be possible.
DVD Video 1 Video 2 Video 3 Tuner FM/AM Tape/MD/CDR CD/Aux 6.1 Direct
Dolby Digital EX/
DTS ES
DSPPro Logic II/
Neo 6
Input
Mode
Stereo
Modes
Dolby Digital EX/
DTS ES
DSPPro Logic II/
Neo 6
Input
Mode
Stereo
Modes