Filter
Top Products
71
English
INTRODUCTION
PREPARATION
BASIC OPERA-
TION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
SOUND FIELD PROGRAM PARAMETER EDITING
4 Press k / n to select the
parameter.
5 Press –/+ to change the
parameter value.
y
• When you set the parameter to a value other than the factory-
set value, an asterisk mark (*) appears by the parameter name
on the video monitor.
6 Repeat steps 3 to 5 above as necessary to
change other program parameters.
Memory back-up
The memory back-up circuit prevents the stored data
from being lost even if this unit is set in the standby
mode, the power cord is disconnected from the AC
outlet, or the power supply is temporarily cut due to
power failure. However, if the power is cut for more
than one week, the parameter value you edited will
return to the factory setting. If so, edit the parameter
value again.
Resetting a Parameter to the
Factory-set Value
■ To reset some of the parameters
to the factory-set values
Select the parameter you want to reset. Then press and
hold –/+ until the value temporarily stops at the factory-
set value. The asterisk mark (*) by the parameter name
disappears on the video monitor.
■ To reset all of the parameters to
the factory-set values
Use “9 PARAM. INI” on the SET MENU to reset all of
the parameter values of all DSP programs within the
selected group to the factory-set values (see page 63).
This operation resets all of the parameter values of all
DSP programs within that group to the factory-set values.
Notes
• The available parameters may be displayed on more than one
OSD page for some of the programs. To scroll through pages,
press k / n.
• You cannot change parameter values when “14 MEMORY
GUARD” on the SET MENU is set to ON. If you want to
change the parameter values, set “14 MEMORY GUARD” to
OFF (see page 65).
Changing Parameter Settings
You can enjoy good quality sound with the factory-set
parameters. Although you do not have to change the
initial settings, you can change some of the parameters to
better suit the input source or your listening room.
Adjustments should be made with the remote control.
y
• We recommended that you edit the parameter while using a
video monitor. It is easier to see the video monitor than it is to
see the front panel display.
1 Set PARAMETER/SET
MENU to PARAMETER.
2 Turn on the video monitor
and press ON SCREEN
repeatedly to select the
full display mode.
3 Select a DSP program you want to adjust.
PARAMETER
SET MENU
P05 ROCK CONCERT
ROOM SIZE…………1.0
LIVENESS…………………5
REV.TIME…………1.6s
REV.DELAY……120ms
REV.LEVEL……………7%
≥ INIT.DLY…………15ms
HALL 1
DSP
10KEY
ROCK
CONCERT
MOVIE
THEATER 1
MOVIE
THEATER 2
TV
SPORTS
MONO
MOVIE
ENTER-
TAINMENT
HALL 2
CHURCH
JAZZ CLUB
SELECT
/DTS
SUR.
1
5
9
6
10
0
10
100
11 12
78
234
+
+
ON SCREEN
Program No.
Example of the parameter setting display
Parameters
Cursor
Program name
HALL 1
6.1/ES
DSP
10KEY
ROCK
CONCERT
MOVIE
THEATER 1
MOVIE
THEATER 2
MUTE
VOLUME
STEREO
TV INPUT
TV VOL
CH
PRESET
DISC
PARAMETER
SET MENU
EFFECT
LEVEL
ON SCREEN
TESTSLEEP
TV MUTE
TV
SPORTS
MONO
MOVIE
ENTER-
TAINMENT
HALL 2
CHURCH
JAZZ CLUB
SELECT
/DTS
SUR.
CHP/INDEX
A/B/C/D/E
1
5
9
6
10
0
10
100
11 12
78
234
++
1
3
4
2
5
Parameter valves
0111V2200_70-75_EN(U) 01.8.1, 9:44 AM71