Filter
Top Products
93 En
Remote control features
ADVANCED
OPERATION
English
You can program remote control codes from other remote
controls. Use the learning feature if you want to program
functions not included in the basic operations covered by
the remote control codes, or an appropriate remote control
code is not available. You can program the function of
other remote control to the buttons in the highlighted areas
in the following illustration. The buttons can be
programmed independently for each control area.
• The remote control transmits infrared rays. If the other remote
control also uses infrared rays, this remote control can learn
most of its functions. However, you may not be able to program
some special signals or extremely long transmissions.
• You cannot program the desired remote control code even if you
select the buttons in the highlighted area in the above
illustration depending on the selected control area and the
assigned library.
1 Set the operation mode selector to
ESOURCE and then press an input selector
button (3) to select the desired control area.
If you want to program the remote control code for
“TV”, set the operation mode selector to ETV.
Make sure that the operation mode selector is set to
E
SOURCE or ETV. When you set the operation mode
selector to EAMP and program a remote control codes
from other remote controls, the programmed key cannot
operate the amplifier function of this unit.
2 Press FSETUP using a ballpoint pen or
similar object.
“SETUP” appears in the display window (4).
3 Press 8k / n repeatedly to select “LEARN”
and then press 8ENTER.
4 Place this remote control about 5 to 10 cm (2
to 4 in) apart from the other remote control
on a flat surface so that their infrared
transmitters are aimed at each other and
then press 8ENTER.
“L–KEY” appears in the display window (4).
5 Press the button for which you want to
program the new function.
“START” appears in the display window (4).
6 Press and hold the button you want to
program on the other remote control until
“OK” appears in the display window (4).
“NG” appears in the display window (4) if learning
was unsuccessful. In this case, start over from step 4.
y
When you want to program another function, repeat steps
4 througn 6.
Programming codes from other
remote controls
Notes
Note
AMP
TV
SOURCE
ZONE
SETUP ID
MACRO
MODE
DVD CD
V-AU X DOCKMULTI
PHONO
AV
POWER
TV
POWER
TV DVR VCR
XM
SIRIUSTUNER
BD
HD DVD
MD
CD-R
CBL
SAT
SRCH MODE
MENU
BAND
TITLE
MEMORY
RETURN
PARAMETER
DISPLAY
MUTE
4
3
SYSTEM MEMORY
2
1
STANDBY
POWER
SELECT
VOLUME
PRESET/CH
ENTER
CAT.
A-E
A
REC
SRCH MODE
MENU
BAND
TITLE
MEMORY
RETURN
PARAMETER
DISPLAY
MUTE
3D DSP
VOLUME
PRESET/CH
ENTER
CAT.
A-E
PRG SELECT
CLASSICAL
1
LIVE/CLUB
2
ENTERTAIN
3
MOVIE
4
STEREO
5
ENHANCER
6
SUR.DECODE
7
STRAIGHT
8
PURE DIRECT
ENT
AUDIO SEL
AUDI O
SLEEP
TV
MUTE
INPUT
9 0
LEVEL
TV CH
INFO
TV VOL
EXTD SUR.
10
REC
Set to
SOURCE
AMP
TV
SOURCE
ZONE
SETUP ID
MACRO
MODE
DVD CD
V-A UX DOCKMULTI
PHONO
AV
POWER
TV
POWER
TV DVR VCR
XM
SIRIUSTUNER
BD
HD DVD
MD
CD-R
CBL
SAT
SRCH MODE
MENU
BAND
TITLE
RETURN DISPLAY
4
3
SYSTEM MEMORY
2
1
STANDBY
POWER
SELECT
VOLUME
PRESET/CH
ENTER
CAT.
A-E
A
PARAMETER
5 to 10 cm (2 to 4 in)
Other remote control
AMP
TV
SOURCE
ZONE
SETUP ID
MACRO
MODE
DVD CD
V-A UX DOCKMULTI
PHONO
AV
POWER
TV
POWER
TV DVR VCR
XM
SIRIUSTUNER
BD
HD DVD
MD
CD-R
CBL
SAT
SRCH MODE
MENU
BAND
TITLE
RETURN DISPLAY
4
3
SYSTEM MEMORY
2
1
STANDBY
POWER
SELECT
VOLUME
PRESET/CH
ENTER
CAT.
A-E
A
PARAMETER
AMP
TV
SOURCE
ZONE
SETUP ID
MACRO
MODE
DVD CD
V-A UX DOCKMULTI
PHONO
AV
POWER
TV
POWER
TV DVR VCR
XM
SIRIUSTUNER
BD
HD DVD
MD
CD-R
CBL
SAT
SRCH MODE
MENU
BAND
TITLE
4
3
SYSTEM MEMORY
2
1
STANDBY
POWER
SELECT
VOLUME
PRESET/CH
A
Other remote control
OK