Filter
Top Products
TRACK
REM
USER
TAPE 1
RAM
HALL
PROG
VOLUME
OVER 15
1234
78910
13 14 15
5
11
6
12
B
A
TRACK
USER
TAPE 1
GRAM
HALL
PROG
VOLUME
OVER 15
1234
78910
13 14 15
5
11
6
12
B
A
E-40
RECORDING COMPACT DISCS
To record programmed tracks from one or
more discs
1 Press the CD input selector button and load a disc (or
discs) on the disc table.
2 Follow steps 3–6 on page 38.
3 Press the PROG button.
* “PROG” and “P-01” will light up on the display, and all
track numbers on the selected disc will begin flashing.
4 If necessary, select a desired disc by pressing the DISC
SKIP button.
5 Select the desired track number by pressing the track
number input buttons.
6 Repeat steps 4 and 5 to program more selections for the
side A of the tape. You can select the same track again.
* Pressing the TIME button displays the total remaining
time on the side of the tape for about 1 second, and
then it is replaced by the display of the next playback
order.
* If “TM OVER” appears on the display, the track number
just selected cannot be programmed because there is
not enough time remaining on the side A of the tape.
However, at this time, if any other track number is
flashing continuously on the display, you can program
it instead of the unprogrammable one.
7 After you finish the programming for the side A, press the
TAPE button.
* “PU SET” appears on the display, then you can begin
programming for side B.
* After this step is done, you can check the programmed
contents for side A and side B alternately by pressing
the TAPE button at any time before you press the EDIT
button in step 9.
8 Repeat steps 4 and 5 to program selections for the side B
of the tape. You can select the same track again.
* If “TM OVER” appears on the display, the track number
just selected cannot be programmed because there is
not enough time remaining on the side B of the tape.
However, at this time, if any other track number is
flashing continuously on the display, you can program
it instead of the unprogrammable one.
9 Press the EDIT button. (“EDIT” appears on the display.)
The recording is automatically started.
Notes on tape-editing
•
If programs are made selecting tracks from more than one
disc, during recording, the DISC CHANGE button on the
CD player is disabled.
•
To check, cancel or correct program data, refer to page
21.
•
The maximum number of tracks that can be programmed
is 20.
•
This function can be used to program up to track number
15. If the disc has more than 15 tracks, track number 16
and thereafter will not be programmed.
Display information during programming
OPEN/CLOSE
DISC CHANGE
Active Servo
Technology
1
2
3
DISC
PROGRAM
USER
VOLUME
DOWN UP
MEMORY
DOWN UP
REC/PAUSE
MODE
NORMAL
DUBBING
HIGH
MEMORY
TIME ADJ
DOLBY NR
AUTO/MAN’L
TIMER
TIMER REC
MUSIC
POWER
PHONES
PRESET/TUNING/BAND
A/B/C/D/E
RANDOM
REPEAT
EDIT
DISPLAY
CD
INPUT INPUT
TAPE 1/2
START
MODE
FREQ PS/PTY/RT/CT
PTY SEEK
MINI COMPONENT SYSTEM
GX
–
70
1
1
2
2
3
3
4
4
5
5
TIME
A
DISC SKIP
PROG
B
TAPE
C
EDIT
D
+I0
E
OPEN
/
CLOSERANDOM
REPEATMODE
6
6
7
7
8
8
9 0
CD
PRESET
TUNER
TAPE
STOP
STOP
PLAY
/
PAUSE
PLAYPLAY
REC
/
PAUSE TAPE 1
/
2
LEVEL MUSIC
TEST FLAT
CENTER
/
REAR
/
DELAY
PROGRAM
USER
POWER
INPUTSLEEP
VOLUME
191
3
7
4
5
9
1
Side of the tape
Selected disc
Next playback order
Programmed track numbers light up
and unprogrammed ones flash.
Selected track
number
Total remaining time on
the side of the tape
TIME
1