Filter
Top Products
E-26
Automatic preset tuning
You can also make use of an automatic preset tuning
function. By this function, this unit performs automatic tuning
and stores stations with strong signals sequentially. Up to 40
stations are stored automatically in the same way as in the
manual preset tuning method on the previous page.
1 Press the INPUT selector or button once or more
so that “TUNER” appears on the display.
2 Press and hold the tuner MEMORY button for about 2
seconds.
* The MEMORY and AUTO indicators will flash.
This unit performs automatic tuning and searches FM and
AM (MW and LW for U.K. and Europe models only) stations
in that order. Received stations are programmed to A1, A2 ...
A8 sequentially.
When the automatic preset tuning is completed
The display shows the frequencies of the first preset station
(stored to A1).
Check the contents and the number of preset stations by
following the procedure of the section “To recall a preset
station” on the previous page.
To recall a preset station
Simply follow the procedure of the section “To recall a preset
station” on the previous page.
Notes
•
The automatic preset tuning search will be performed
through all frequencies until 40 stations are stored. If the
number of received stations is less than 40, the search will
stop after searching all frequencies.
* Since FM stations are searched for first, there may be a
case that 40 preset stations are occupied by FM
stations only.
•
<U.K. and Europe models only>
The unit is originally set so that only RDS stations are
searched instead of all FM stations by this operation. (FM
stations that employ no RDS network service cannot be
programmed.)
However, you can change the setting so that the unit can
program not only RDS stations but also other FM stations.
(Refer to page 30 for details.)
•
With this function, only stations with sufficient signal
strength are stored automatically. If the station you want
to program is weak in signal strength, tune to it in
monaural manually and program it by following the
procedure of the section “To store stations” on the
previous page.
•
You can replace a preset station by another FM or AM
(MW or LW) station manually by simply following the
procedure of the section “To store stations” on the
previous page.
1
PLAYBACK
2
REC/PLAYBACK
EJECT
OPEN/CLOSE
DISC CHANGE
Active Servo
Technology
1
2
3
DISC
PROGRAM
USER
VOLUME
DOWN UP
MEMORY
DOWN UP
REC/PAUSE
MODE
HOUR MIN
NORMAL
DUBBING
HIGH
MEMORY
TIME ADJ
DOLBY NR
AUTO/MAN’L
TIMER
TIMER REC
MUSIC
POWER
PHONES
PRESET/TUNING/BAND
A/B/C/D/E
RANDOM
REPEAT
EDIT
DISPLAY
CD
INPUT INPUT
TAPE 1/2
START
MODE
FREQ PS/PTY/RT/CT
PTY SEEK
EJECT
MINI COMPONENT SYSTEM
GX
–
70
TUNING OPERATION
1
1
2
2
3
3
4
4
5
5
TIME
A
DISC SKIP
PROG
B
TAPE
C
EDIT
D
+I0
E
OPEN
/
CLOSERANDOM
REPEATMODE
6
6
7
7
8
8
9 0
CD
PRESET
TUNER
TAPE
STOP
STOP
PLAY
/
PAUSE
PLAYPLAY
REC
/
PAUSE TAPE 1
/
2
LEVEL MUSIC
TEST FLAT
CENTER
/
REAR
/
DELAY
PROGRAM
USER
POWER
INPUTSLEEP
VOLUME
21
1
Memory back-up
The memory back-up circuit prevents the programmed
data from being lost even if the AC supply lead is
disconnected from the AC outlet or the power is cut due
to temporary power failure. If, however, the power is cut
for more than one week, the memory may be erased. If
so, it can be re-programmed by simply following the
Preset tuning steps.