Filter
Top Products
(REAR PANEL CONT.)
PARTS AND FUNCTIONS
9
LEFT AND RIGHT CHANNEL “PRE” OUTPUT JACKS: These
two output jacks can be used to connect an external tape
deck on which to record music AND vocals, being played
on the
Bravo. Connect the left “L” and right “R” “PRE” out-
put jacks of the Bravo to the respective left “L” and right “R”
input jacks (usually “REC IN” on most tape decks) on the
back of your external tape deck. (Follow
instructions for using either player on the Bravo) Play the
desired CD/CDG or cassette on the Bravo and record it on
your external tape deck.
10
VIDEO INPUT JACKS: There are two video input jacks on the
back of the
Bravo. They both serve the same purpose and
can be used to connect two external players at a time. They
are labeled separately, “DVD” (digital video disc) and “LD”
(laser disc), to allow you to easily identify which jack you have
connected to which player. When a DVD or LD player has
been properly connected, (See “CONNECTING OTHER COM-
PONENTS TO THE BRAVO”), the television monitor con-
nected to the Bravo will display lyrics and graphics from the
discs being played on the external player(s). To connect an
external player use an RCA connector cable. Connect either
the DVD or LD VIDEO INPUT jack on the back of the Bravo
to the “VIDEO OUTPUT” jack on the external respective player.
The basic rule is “INPUT” connected to OUTPUT”. WHEN
PLAYING AND EXTERNAL DVD OR LD PLAYER, BE SURE TO
SELECT THE DVD OR LD SETTING ON THE FRONT OF THE
BRAVO, OTHERWISE THERE WILL BE NO AUDIO OR VIDEO.
(See FRONT PANEL diagram, #26, #27)
11
RIGHT AND LEFT AUDIO INPUT JACKS TO CONNECT
EXTERNAL LASER DISC (LD) PLAYER: The “R” and “L”
“AUDIO INPUT” jacks are used to connect an external laser
disc player to the
Bravo. When properly connected,
the Bravo will play the music being played on the
laser disc player through the Bravo speakers.
Connect the “R” and “L” “AUDIO INPUT” jacks on the Bravo
to the “L” and “R” “AUDIO OUTPUT” jacks on the laser disc
player, using an RCA type connector cable. WHEN
PLAYING AND EXTERNAL LD PLAYER, BE SURE TO SELECT
LD SETTING ON THE FRONT OF THE BRAVO,
OTHERWISE THERE WILL BE NO AUDIO OR VIDEO.
12
RIGHT AND LEFT AUDIO INPUT JACKS TO CONNECT
AN EXTERNAL DIGITAL VIDEO DISC (DVD) PLAYER: The “R”
and “L” “AUDIO INPUT” jacks are used to connect an exter-
nal laser disc player to the
Bravo. When properly connected,
the Bravo will play the music being played on the laser disc
player through the Bravo speakers. Connect the “R” and
“L” “AUDIO INPUT” jacks on the Bravo to the “L” and “R”
“AUDIO OUTPUT” jacks on the laser disc player, using an
RCA type connector cable. WHEN PLAYING AND EXTERNAL
LD PLAYER, BE SURE TO SELECT LD SETTING ON THE
FRONT OF THE BRAVO, OTHERWISE THERE WILL BE NO
AUDIO OR VIDEO.
13
16
VIDEO OUTPUT JACK: The video output jack is used to
connect the
Bravo to a television monitor. When properly
connected, the television monitor will display lyrics and graph-
ics from CDG discs being played on the Bravo. There are
three ways to connect a television monitor to the Bravo. 1)
Connect the “VIDEO OUTPUT” jack to the “VIDEO IN” on the
back of the television monitor. There is an RCA connector
cord provided with the
Bravo for this type of connection. BE
SURE TO SWITCH YOUR TELEVISION MONITOR TO “VIDEO”
MODE, OTHERWISE LYRICS AND GRAPHICS WILL NOT AP-
PEAR. 2) If your television monitor does not have and RCA
type connector and only has a coaxial connector, you can use
the built-in RF Modulator on the back of the Bravo. (See dia-
gram on opposite page). 3) For PAL TV systems without
video inputs: Connect The Bravo to an RF Modulator through
the video output jacks on the Bravo. (See diagram on
opposite page.)