Filter
Top Products
(REAR PANEL CONT.)
PARTS AND FUNCTIONS
11
LEFT AND RIGHT CHANNEL RECORD (“REC”) OUTPUT
JACKS: These two outputs jacks can be used to connect an
additional tape deck. Connect the left (“L”) and right (“R”)
record (REC) output jacks to the respective left (“L”) and right
(“R”) record (REC) input jacks on the back of your external
tape deck. Only the music being played on the CDG X-3
Mark II will record onto your external tape deck. (Follow in-
structions for using either player on the CDG X-3 Mark II) Play
the desired CD/CDG or cassette on the CDG X-3 Mark II and
record it on your external tape deck. Vocals from the CDG X-
3 Mark II will not be recorded using these jacks. To record
music and vocals from the CDG X-3 Mark II to an external
tape deck connect your external tape deck to the “L” AND
“R” “PRE” output jacks of the “AUDIO OUTPUT” section.
(See #16 on REAR PANEL diagram. Also see “CONNECT-
ING OTHER COMPONENTS TO THE CDG X-3 MARK II ”,
“Expanding Your System”)
10
AC POWER CORD: Plugs into any AC wall outlet.
12
LEFT AND RIGHT CHANNEL “PRE” OUTPUT JACKS: These
two output jacks can be used to connect an external tape
deck on which to record music AND vocals, being played
on the CDG X-3 Mark II. Connect the left “L” and right “R”
“PRE” output jacks of the CDG X-3 Mark II to the respective
left “L” and right “R” input jacks (usually “REC IN” on most
tape decks) on the back of your external tape deck. (Follow
instructions for using either player on the CDG X-3 Mark II)
Play the desired CD/CDG or cassette on the CDG X-3 Mark II
and record it on your external tape deck.
13
VIDEO OUTPUT JACK: The video output jack is used to
connect the CDG X-3 Mark II to a television monitor. When
properly connected, the television monitor will display lyrics
and graphics from CDG discs being played on the CDG X-3
Mark II. There are three ways to connect a television monitor
to the CDG X-3 Mark II. 1) Connect the “VIDEO OUTPUT”
jack to the “VIDEO IN” on the back of the television monitor.
There is an RCA connector cord provided with the CDG X-3
Mark II for this type of connection. BE SURE TO SWITCH YOUR
TELEVISION MONITOR TO “VIDEO” MODE, OTHERWISE LYR-
ICS AND GRAPHICS WILL NOT APPEAR. 2) If your television
monitor does not have and RCA type connector and only has
a coaxial connector, you can use a VCR to connect the CDG
X-3 Mark II to your television monitor. To do this, connect the
“VIDEO OUTPUT” jack on the back of the CDG X-3 to the
“VIDEO IN” on the VCR. (See diagram on opposite page). BE
SURE THE TELEVISION MONITOR IS SET TO “ VIDEO” MODE
AND THE VCR SETTING CORRESPONDS TO THE JACKS YOU
HAVE CONNECTED THE PLAYER TO, OTHERWISE LYRICS
AND GRAPHICS WILL NOT APPEAR. If you are unsure of
which setting on the VCR should be used, see manufacturer’s
instructions provided with the VCR. 3) If you do not have a
VCR, or RCA connectors on the back of your television moni-
tor. You will need an “RF” modulator.
To use an “RF” modulator, connect the “VIDEO OUTPUT”
jack on the back of the CDG X-3 Mark II to the “VIDEO IN” jack
on the “RF” modulator. Next, Connect the “OUTPUT” of the
“RF” modulator, with a coaxial cable (not provided) , to the
“ANTENNA INPUT” of the television monitor. BE SURE
TO SET THE TELEVISION MONITOR TO “CHANNEL 3”,
OTHERWISE LYRICS AND GRAPHICS WILL NOT APPEAR.
(Refer to diagram on opposite page)
VIDEO INPUT JACKS: There are two video input jacks on the
back of the CDG X-3 Mark II. They both serve the same pur-
pose and can be used to connect two external players at a
time. They are labeled separately, “DVD” (digital video disc)
and “LD” (laser disc), to allow you to easily identify which jack
you have connected to which player. When a DVD or LD player
has been properly connected, (See “CONNECTING OTHER
COMPONENTS TO THE CDG X-3 MARK II”), the television
monitor connected to the CDG X-3 Mark II will display lyrics
and graphics from the discs being played on the external
player(s). To connect an external player use an RCA connec-
tor cable. Connect either the DVD or LD VIDEO INPUT jack
on the back of the CDG X-3 Mark II to the “VIDEO OUTPUT”
jack on the external respective player. The basic rule is “IN-
PUT” connected to OUTPUT”. WHEN PLAYING AND EXTER-
NAL DVD OR LD PLAYER, BE SURE TO SELECT THE DVD OR
LD SETTING ON THE FRONT OF THE CDG X-3 MARK II, OTH-
ERWISE THERE WILL BE NO AUDIO OR VIDEO. (See FRONT
PANEL diagram, #26, #27)
14
RIGHT AND LEFT AUDIO INPUT JACKS TO CONNECT
EXTERNAL LASER DISC (LD) PLAYER: The “R” and “L”
“AUDIO INPUT” jacks are used to connect an external laser
disc player to the CDG X-3 Mark II. When properly connected,
the CDG X-3 Mark II will play the music being played on the
laser disc player through the CDG X-3 Mark II speakers.
Connect the “R” and “L” “AUDIO INPUT” jacks on the CDG X-
3 Mark II to the “L” and “R” “AUDIO OUTPUT” jacks on the
laser disc player, using an RCA type connector cable. WHEN
PLAYING AND EXTERNAL LD PLAYER, BE SURE TO SELECT
LD SETTING ON THE FRONT OF THE CDG X-3 MARK II,
OTHERWISE THERE WILL BE NO AUDIO OR VIDEO.
15
RIGHT AND LEFT AUDIO INPUT JACKS TO CONNECT
AN EXTERNAL DIGITAL VIDEO DISC (DVD) PLAYER: The “R”
and “L” “AUDIO INPUT” jacks are used to connect an exter-
nal laser disc player to the CDG X-3 Mark II. When properly
connected, the CDG X-3 Mark II will play the music being
played on the laser disc player through the CDG X-3 Mark II
speakers. Connect the “R” and “L” “AUDIO INPUT” jacks on
the CDG X-3 Mark II to the “L” and “R” “AUDIO OUTPUT” jacks
on the laser disc player, using an RCA type connector cable.
WHEN PLAYING AND EXTERNAL LD PLAYER, BE SURE TO
SELECT LD SETTING ON THE FRONT OF THE CDG X-3 MARK
II, OTHERWISE THERE WILL BE NO AUDIO OR VIDEO.
16
16