Filter
Top Products
ENGLISH
18
In Dolby Digital, Dolby Pro Logic II, Dolby
Pro Logic or Dolby Virtual mode, adjusting
delay times of the speakers
The delay time will be displayed for 5 seconds.
The corresponding delay time is displayed. The
center delay time can be adjusted in the Dolby
Digital mode only.
In the Dolby Virtual mode, “NARROW” or
“WIDE” is displayed.
Each time this button is pressed in the Dolby
Digital, Dolby Pro Logic II or Dolby Pro Logic
mode, the delay time changes in regular intervals.
Each time this button is pressed in the Dolby Virtual
mode, the delay mode changes as follows:
NARROW: Relatively long distance from the
prime listening position to front
speakers.
WIDE: Relatively short distance.
If the delay time disappears, start from the step 17
again.
In case of Dolby Digital, Dolby Pro Logic II or Dolby
Pro Logic mode, when the distances from the prime
listening position to front left, center, front right, rear
left and rear right speakers are same, the basic settings
are as follows according to the surround modes;
- In the Dolby Digital mode,
Center delay time : 0 ms, Rear delay time : 0 ms
- In the Dolby Pro Logic II Music, Matrix or Custom mode,
Rear delay time : 0 ms
- In the Dolby Pro Logic II Movie, Dolby Pro Logic mode,
Rear delay time : 10 ms
If the center or the rear speaker(s) is(are) not at the
same distance from the prime listening position as the
front speakers, increase or decrease the center delay
time by 1 ms for every about 30 cm(1 foot) it is closer
or farther away and increase or decrease the rear delay
time by 5 ms for every about 1~1.5 m(3~5 feet) it is
closer or farther away.
Downmixing into 2 front channels
To cancel the 2-CH downmix mode, select the
desired surround mode with using the DSP MODE
button.
When the playback of the source on the player is
stopped or interrupted, etc., the 2-CH downmix
mode is not canceled even though “ST” and the
DTS or Dolby Digital indicators go off.
If the headphones are plugged and the SPEAKER
button is set to off while the digital signals from the
DTS and Dolby Digital program sources are being
input, it will enter the 2-CH downmix mode
automatically(but only the DTS or Dolby Digital
indicator lights up still) and if the headphones are
unplugged and the SPEAKER button is set to on in
the 2-CH downmix mode, it will return to the
previous mode.
Allows the multi-channel DTS or Dolby Digital signals
to be reproduced through only two speakers or through
headphones.
When the digital signals from the DTS or Dolby Digital
program sources are input in available surround mode,
press the STEREO button.
“ST” and the DTS or Dolby Digital indicators light up,
meaning it enters the 2-CH downmix mode, and then the
discrete multi-channels(except LFE) are mixed down into
2 front channels.
Adjust the delay time.
18
Check the delay time
to be adjusted.
17
In Dolby Digital mode, repeat the above
steps 17 and 18 to adjust the rear delay
time.
19
POWER
DISPLAY
SLEEPVIDEO1
123VIDEO2
456VIDEO3
789CD
T.TONE
0 P.SCANTUNER
DSP MODE
D.TIMEADJUSTAUX
MUTE T.MON
CH. LEVEL
CH. SEL
MASTER VOLUME
REMOTE CONTROL UNIT RM-105
D.TIME
AUTO
POWER
DISPLAY
SLEEPVIDEO1
123VIDEO2
456VIDEO3
789CD
T.TONE
0 P.SCANTUNER
DSP MODE
D.TIMEADJUSTAUX
MUTE T.MON
CH. LEVEL
CH. SEL
MASTER VOLUME
REMOTE CONTROL UNIT RM-105
ADJUST
AUTO
STEREO