Filter
Top Products
ENGLISH
17
Enter the test tone mode.
14
Only when it is in available surround modes except
the Dolby Virtual and stereo modes, the volume
level of each channel can be adjusted easily with the
test tone function.
Note: When the 6 CH DIRECT is selected as an input
source, the test tone function does not work.
At each channel, adjust the level as desired
until the sound level of each speaker is
heard to be equally loud.
15
Cancel the test tone function.
16
Adjusting each channel level
Adjusting each channel level with
test tone
Select the desired channel.
11
Adjust the level of the selected channel
as desired.
12
Repeat the above steps 11 and 12 to
adjust other channel levels.
13
The LFE level can be adjusted within the range of
-10~0 dB and other channel levels within the range
of -15~+15 dB.
In general, we recommend the LFE level to be
adjusted to 0 dB. (However, the recommend LFE
level for some early DTS software is -10 dB.) If the
recommended levels seems too high, lower the
setting as necessary.
If the channel display disappears, start from the
above step 11 again.
Each time this button is pressed, the corresponding
channel is selected and displayed for 3 seconds as
follows;
Front Left Center Front Right Rear Right
(Dolby Digital or DTS L(FE) )SubWoofer Rear Left
( ): Adjustable only when the digital signals from Dolby Digital or
DTS program source that includes LFE signal are input in the
available surround mode.
When it is in the stereo or Dolby Virtual mode, or
the speaker setting is “N”, center, rear or subwoofer
channel will not be selected.
The test tone will be heard from the speaker of each
channel for 2 seconds as follows;
Front Left Center Front Right
SUBwoofer Rear Left Rear Right
When the speaker setting is “N”, the test tone of the
corresponding channel is not available.
When the selected decoding mode is not matched to the
input signal format, the test tone function cannot work.
or
CHANNEL
SELECTOR
POWER
DISPLAY
SLEEPVIDEO1
123VIDEO2
456VIDEO3
789CD
T.TONE
0 P.SCANTUNER
DSP MODE
D.TIMEADJUST AUX
MUTE T.MON
CH. LEVEL
CH. SEL
MASTER VOLUME
REMOTE CONTROL UNIT RM-105
AUTO
CH. SEL
or
ADJUST
POWER
DISPLAY
SLEEPVIDEO1
123VIDEO2
456VIDEO3
789CD
T.TONE
0 P.SCANTUNER
DSP MODE
D.TIMEADJUST AUX
MUTE T.MON
CH. LEVEL
CH. SEL
MASTER VOLUME
REMOTE CONTROL UNIT RM-105
CH. LEVEL
AUTO
You can select the desired channel and adjust its
level with repeating the steps 11 and 12 in
“Adjusting each channel level” procedure.
or
ADJUST
POWER
DISPLAY
SLEEPVIDEO1
123VIDEO2
456VIDEO3
789CD
T.TONE
0 P.SCANTUNER
DSP MODE
D.TIMEADJUST AUX
MUTE T.MON
CH. LEVEL
CH. SEL
MASTER VOLUME
REMOTE CONTROL UNIT RM-105
CH. LEVEL
AUTO
POWER
DISPLAY
SLEEPVIDEO1
123VIDEO2
456VIDEO3
789CD
T.TONE
0 P.SCANTUNER
DSP MODE
D.TIMEADJUST AUX
MUTE T.MON
CH. LEVEL
CH. SEL
MASTER VOLUME
REMOTE CONTROL UNIT RM-105
T.TONE
AUTO
POWER
DISPLAY
SLEEPVIDEO1
123VIDEO2
456VIDEO3
789CD
T.TONE
0 P.SCANTUNER
DSP MODE
D.TIMEADJUST AUX
MUTE T.MON
CH. LEVEL
CH. SEL
MASTER VOLUME
REMOTE CONTROL UNIT RM-105
T.TONE
AUTO