Filter
Top Products
ENGLISH
14
ENTERING A SETUP CODE
• This remote control can control up to eight different components.
• Before operating audio and video components using the remote control supplied with this receiver, the setup code for each
component should be entered.
• Because only the setup codes for CD player and DVD player among Sherwood components are listed in the operating manual of this
remote control, when entering a setup code for Sherwood components for system remote control operation, find the corresponding setup
code in the “FUNCTION TABLE of the NUMBERED BUTTONS” on page 11 in this operating instructions. For your reference, the setup
cord for each Sherwood component such as CD player, tape deck and DVD player(V-756, etc.) is “001” respectively.(However, the setup
code for some Sherwood DVD player such as VD-4103, etc. is “057”, “074”, “112”, “114”.) Enter each setup code for CD player and tape
deck doing steps , and as follows.
DVD
VOL.
CH LEVEL
OSD
CH SEL
DSP
MODE
AUTO
ST
CENTER
MODE
TEST
TONE
DISC
P.SCAN
TUNER
CD
T1/MONAUX
PHONO
VID1 VID2 VID3 VID4 VID5
SYS DISPSLEEP
DIRECT IN
ROOM2
INTRO
RETURN
B
RPT
A
7.1 SURR
TITLE
ENTER
HOME THEATER MASTER
RNC-220
For receiver or amplifier :
For CD player :
For CABLE :
DVD
VOL.
CH LEVEL
OSD
CH SEL
DSP
MODE
AUTO
ST
CENTER
MODE
TEST
TONE
DISC
P.SCAN
TUNER
CD
T1/MONAUX
PHONO
VID1 VID2 VID3 VID4 VID5
SYS DISPSLEEP
DIRECT IN
ROOM2
INTRO
RETURN
B
RPT
A
7.1 SURR
TITLE
ENTER
HOME THEATER MASTER
RNC-220
For receiver or amplifier :
For CD player :
For CABLE :
Repeat the above steps to for each
of your other components.
7
Operate the component using the
corresponding function buttons on the remote
control such as POWER, CH and
VOL buttons, etc.
6
Example) The correct setup code for this receiver is
“001”.
If any of the buttons do not perform as they should
start from step again to enter the next setup code.
Note:
Some audio and video components have separate
buttons for POWER ON/OFF.
In this case, press the corresponding DEVICE button
to turn the component ON and press the POWER
button to turn the component OFF.
If there is no correct setup code or if the
Manufacturer/Brand for your component is not listed
in “Set-Up Code Table” in the operating manual of
this remote control, please use the “Auto Search
Method” on page 10 in the operating manual of this
remote control.
Although each setup code is designed to work with
many different modes, certain codes may not work with
some models. (Also, certain codes may only operate
some of the functions available on a given model.)
Find the setup code for your component
referring to “Set-Up Code Table” in the
operating manual of this remote control.
2
Turn on the component you want to control.
1
Example) When entering the setup code for this
receiver, turn on this receiver.
DVD
VOL.
CH LEVEL
OSD
CH SEL
DSP
MODE
AUTO
ST
CENTER
MODE
TEST
TONE
DISC
P.SCAN
TUNER
CD
T1/MONAUX
PHONO
VID1 VID2 VID3 VID4 VID5
SYS DISPSLEEP
DIRECT IN
ROOM2
INTRO
RETURN
B
RPT
A
7.1 SURR
TITLE
ENTER
HOME THEATER MASTER
RNC-220
001
102
For "001" :
For "102" :
Enter the 3 digit setup code aiming the remote control
at the REMOTE SENSOR on the component.
4
Press the corresponding DEVICE and the
MUTE buttons simultaneously.
3
Your component will be turned off when the correct
setup code is entered.
Continue to enter the corresponding codes until your
component turns off.
If the LED lamp and the corresponding DEVICE
button go off, start from the step
again.
Then the LED lamp and the corresponding DEVICE
button on the remote control light up for 20 seconds.
Then the LED lamp and the corresponding DEVICE
button will flicker twice.
5
Press the corresponding DEVICE button to
store the setup code.