Filter
Top Products
YO <P=001>
(Continued)
When an error message is displayed, proceed as follows:
Error messages
Meaning
Remedy
BLANK MD
● Nothing is recorded. ● Replace it with another disc.
Can’t COPY
● You tried to record from a copy-protected disc.
● Replace it with a regular disc that can be copied.
Can’t EDIT
● A track cannot be edited.
● Change the stop position of the track and then try editing
it.
Can’t REC
● Recording cannot be performed correctly due to vibra-
tion or shock in the unit.
● Re-record.
Can’t T REC
● Timer recording is impossible or there is no available
space on the MD.
● Replace it with another disc.
CH ERROR
● There is something wrong with the CD changer.
● Set this unit to the stand-by mode and then back to on,
and press the button.
CONNECT ERR
● Whilst an MD player is being edited on this unit, incorrect
digital signals are input from the portable MD player.
● Make sure the cable is connected correctly and that
power is being supplied to the portable MD player.
DEFECT
● Since this disc has scratches on it, the recording oper-
ation was skipped.
● Replace it with another disc.
Din UNLOCK
● Incorrect digital signals are input.
● Connect correct digital signals.
● Use the analogue input sockets.
DISC ERR
● The disc is damaged.
● A TOC is not written on the MD or there is something
wrong with data.
● Reload the disc or replace it.
DISC FULL
● The disc is out of recording space.
● Replace the disc with another recordable disc.
EDIT OVER
● There is no space to make CD editing on the disc.
● Replace it with a disc that has enough time to record.
FOCUS ERROR
● A disc has not been loaded.
● The disc data cannot be read.
● Reload the MiniDisc.
MD ERROR
● No operation.
● Contact the shop where you purchased the unit.
MECHA ERR∗
(∗:Number or
symbol)
● There is a mechanical problem and the disc is not work-
ing properly.
● Set this unit to the stand-by mode and press the but-
ton.
NAME FULL
● The number of characters for the disc name or track
name exceeds 100.
● Shorten the disc or track name.
NO DISC
● A disc has not been loaded.
● The disc data cannot be read.
● Load a disc.
● Reload the disc.
NOT AUDIO
● The data recorded on this disc is not audio data. ● Select another track.
● Replace the disc.
PLAYBACK MD
● You tried to record on a playback-only disc.
● Replace it with another recordable disc.
PROTECT
● Trouble is found. ● Restart the unit. If the unit doesn’t work, contact a
SHARP Authorised Servicing Dealer or SHARP Auth-
orised Service station.
PROTECTED
● The disc is write protected.
● The tape is protected against accidental erasure.
● Move the write protection tab back to its original position.
● Cover the accidental erase prevention hole.
TAPE ERROR
● The tape mechanism is defective.
● Try pressing the RESET button.
TEMP OVER
● The temperature is too high.
● Set this unit to the stand-by mode and wait for a while.
TOC ERR∗
(∗:Number or
symbol)
● The disc is damaged.
● TOC information cannot be read.
● MD not specified.
● Replace it with another disc.
TOC FULL∗
(∗:Number or
symbol)
● There is no space left for recording character information
(track names, disc names, etc.).
● Replace it with another recordable disc.
TOC W ERROR
● Recording is impossible.
● Contact the shop where you purchased the unit.
TRAY ERROR
● The CD tray operates incorrectly.
● Unplug the AC power lead, plug it back, and then turn
the power on.
U TOC ERR∗
(∗:Symbol)
● TOC information recorded on the MD does not match
the MD specifications or it cannot be read.
● Replace it with another disc.
● Erase all of the track, and try recording.
U TOC W ERR
● The TOC information could not be created properly due
to a mechanical shock or to scratches on the disc.
● Set this unit to the stand-by mode and try to write the
TOC again.
(Remove any source of shock or vibration whilst writing.)
? DISC
● The data contains an error.
● Replace it with another disc.
00:00
● Music is not being recorded.
● Replace the disc with another recordable disc.
MD-X60H(SUK) TINSE0227AWZZ
53