Filter
Top Products
04/1/28 CD-DH790NH EN
17
2
1
7
6
5
4
3
2
1
Listening to the radio
Auto power on function:
When you press any of the following buttons, the unit turns
on.
●
TUNER (BAND) button (remote control only): The unit
turns on and the “TUNER” function is activated.
●
/ button on the main unit: The unit turns on and
playback of the last function starts (CD, TUNER,
AUDIO IN, USB, iPod, TAPE).
Note:
This product can receive FM stereo/FM monaural and AM
monaural broadcasts. AM stereo broadcasts will not be
played in stereo.
Notes:
●
When radio interference occurs, auto scan tuning may
stop automatically at that point.
●
Auto scan tuning will skip weak signal stations.
●
To stop the auto tuning, press the TUNING ( or )
button again.
●
When an RDS (Radio Data System) station is tuned in,
the frequency will be displayed first, and then the RDS
indicator will light up. Finally, the station name will
appear.
●
Full auto tuning can be achieved for RDS stations
“ASPM”, see page 18.
To receive an FM stereo transmission:
●
Press the FUNCTION button on main unit or TUNER
(BAND) button on remote control repeatedly to select
stereo mode and “ST” indicator will be displayed. “ ”
will appear when an FM broadcast is in stereo.
●
If the FM reception is weak, press the TUNER (BAND)
button to extinguish the “ST” indicator. The reception
changes to monaural, and the sound becomes clearer.
You can store 40 AM and FM stations in memory and recall
them at the push of a button. (Preset tuning)
Note:
The backup function protects the memorised stations for a
few hours should there be a power failure or the AC power
lead become disconnected.
Press the PRESET ( or ) button for less than 0.5
seconds to select the desired station.
The stations saved in the memory can be scanned
automatically. (Preset memory scan)
■
Tuning
1
Press the ON/STAND-BY button to turn the power on.
2
Press the FUNCTION button on the main unit or
TUNER (BAND) button on the remote control
repeatedly to select the desired frequency band (FM
stereo, FM mono or AM).
3
Press the TUNING ( or ) button to tune in to the
desired station.
●
Manual tuning:
Press the TUNING ( or ) button repeatedly to
tune in to the desired station.
●
Auto tuning:
When the TUNING ( or ) button is pressed for
more than 0.5 seconds, scanning will start
automatically and the tuner will stop at the first
receivable broadcast station.
CD
USB
FUNCTION
FUNCTION
VOL
VOL
ON/STAND-BY
ON/STAND-BY
MINI COMPONENT SYSTEM
CD-DH790
ON/STAND-BY
ON/STAND-BY
■
Memorising a station
1
Perform steps 1 - 3 in “Tuning”.
2
Press the MEMORY button.
3
Within 30 seconds, press the PRESET ( or ) button
to select the preset channel number. Store the stations
in memory, in order, starting with preset channel 1.
4
Within 30 seconds, press the MEMORY button to store
that station in memory. If the “MEMORY” and preset
number indicators disappear before the station is
memorised, repeat the operation from step 2.
5
Repeat steps 1 - 4 to set other stations, or to change a
preset station. When a new station is stored in the
memory, the station previously memorised for that
preset channel number will be erased.
■
To recall a memorised station
■
To scan the preset stations
1
Press the PRESET ( or ) button for more than 0.5
seconds. The preset number will flash and the
programmed stations will be tuned in sequentially, for 5
seconds each.
2
Press the PRESET ( or ) button again when the
desired station is located.
■
To erase entire preset memory
1
Press the ON/STAND-BY button to enter the stand-by
mode.
2
Whilst pressing down the FUNCTION button, press the
ON/STAND-BY button until “TUNER CLEAR” appears.
ON/STAND-BY
ON/STAND-BY