Filter
Top Products
26
RSX-972 Surround Sound Receiver
OTHER OPTIONS Menu
OTHER OPTIONS
RECORD: CD
DYNAMIC: Max
5.1CH: Off
POWER: Direct
LANGUAGE: English
ENT KEY=MAIN MENU UP KEY=up
+/– KEY=change DWN KEY=down
This menu, accessed from the MAIN menu,
provides access to a several miscellaneous
settings as follows:
RECORD: Select a signal for the record out-
puts by choosing one of the input sources.
DYNAMIC: steps through the three dynamic
range settings available in digital modes:
• MAX (no compression/full dynamic range)
• MID (moderate compression)
• MIN (full compression/minimum dynamic
range).
5.1CH: determines whether or 5.1 channel
input is turned ON or OFF.
POWER: This setting determines how the
RSX-972 powers up. With the default DIRECT
setting, the unit is fully activated when AC power
is applied and the front-panel POWER button
is pressed in; however, it may be put in
STANDBY mode using the remote POWER
button. With the STANDBY setting, the unit pow-
ers up in standby mode when AC is applied
and the front-panel POWER button is in the
ON position. The unit must be activated us-
ing the remote control POWER button. In AL-
WAYS-ON mode, the unit remains fully active
whenever AC is present and the front-panel
POWER button is pressed in; the remote
POWER button is disabled and the unit can-
not be put in standby mode.
LANGUAGE: Selects one of the languages
for all of the ON-SCREEN MENUS: English
or German (Deutsch).
Change settings on the OTHER OPTIONS menu
by highlighting the desired line using the UP/
DOWN buttons and using the +/– buttons to
step through the available settings. To return
to the MAIN menu, press the ENTER button.
Press the MENU key on the remote to cancel
the display and return to normal operation.
RESET Menu
Reset to factory
default settings:
YES = ENT KEY
NO = DWN KEY
The FACTORY DEFAULT menu resets all sys-
tem configuration settings to the factory sup-
plied settings. This menu is reached by high-
lighting the RESET line on the MAIN menu and
pressing ENTER.
Press the ENTER button to reset all settings. Press
the DOWN button to cancel this menu and
return to the MAIN menu without restoring the
default settings.
NOTE
: Resetting to factory default settings will
erase all stored settings including delay set-
tings, speaker settings, balance settings, in-
put settings and more. You will lose ALL system
configuration settings. Be certain that you wish
to do so before resetting the factory defaults.
ZONE 2 SETUP Menu
ZONE2 SETUP
SOURCE: CD
VOLUME SETUP: Variable
VOLUME: 20
ENT KEY=MAIN MENU UP KEY=up
+/– KEY=change DWN KEY=down
The ZONE 2 SETUP menu provides settings
and configuration options related to the op-
eration of Zone 2. This menu is reached by
highlighting the ZONE 2 line on the MAIN
menu and pressing ENTER.
SOURCE: the source selected for listening in
Zone 2. Selecting the OFF option turns Zone
2 off.
VOLUME SETUP: configures the Zone 2
outputs for VARIABLE or FIXED volume levels.
VARIABLE allows control of the volume settings
in Zone 2 from the RSX-972 front-panel or from
a remote control and IR repeater in Zone 2.
FIXED output disables the Zone 2 volume
control. In this mode, the Zone 2 level can be
fixed at the level specified on the next line,
thus optimizing system performance when send-
ing a fixed level signal to a preamp or ampli-
fier with its own volume adjustment.
VOLUME: In VARIABLE output mode, this line
shows the current volume setting for Zone 2.
In FIXED output mode, this use this setting to
establish a permanent fixed output level for
Zone 2.
Move the highlight to the desired line using
the UP/DOWN buttons and use the +/– but-
tons to adjust the volume level. To return to the
MAIN menu, press the ENTER button. Press
the MENU key on the remote to cancel the
display and return to normal operation.