Filter
Top Products
Line 0 is used for displaying chapter, frame, time and track numbers.
Line 0 and 1 are sometimes used for displaying remote control inputs.
Line 2 to 9 are used exclusively as the User’s Display Area on the CLD-
V2800.
If all lines of the User’s Display Area are required for user defined messages,
the 4RA command can be sent to the player. This will reserve all lines
(including lines 0 and 1) in the display for user messages.
NOTE: Lines 0 & 1 are usually reserved for frame/time and chapter/track
addresses and the address flag status.
To activate the User Display Area:
• Set the User’s Display using the Register A command.
• Turn ON the display switch. (1DS)
• Identify the line on which the characters will appear by using the Print
Character command (PR) <CR>. (See page 3-30.)
• Then send the character string to be displayed followed by <C/R>.
NOTE: The display switch can be turned ON or OFF at any time. However, if Register A
is changed so that the User’s Display Area is disabled, the contents of the User’s
Display Area will be cleared. Also, if the Print Character command is issued before
Register A is set for the User’s Display Area, the character string will not be seen. The
Power-On default for display control is 3RA. This allows Frame/Time, Chapter/Track
numbers to be seen when the display is turned on, depending on the type of disc that is
in the tray. Register A may be changed for different displays. See example below:
Chapter Three • CLD-V2800 Level III
3-40 TP 120 v. 1.0 • 10/95 CLD-V2800 Level III User’s Manual
Figure 3-S
■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
■ ■ ■ ■ ■ ■ ■ User’s Area ■ ■ ■ ■ ■ ■
■ ■ ■ ■ ■ 10 lines x 20 Characters ■ ■ ■ ■
■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
Line 0
Line 1
2
3
4
5
6
7
8
9
Chapter (CAV or CLV) (2)
Track-Index (CD) (4)
Frame (CAV) or Time (CLV) (5)
Time or Time+ Block (CD) (4 or 6)