Filter
Top Products
5 minute guide
02
9
En
1 Switch on the receiver and your TV.
2 Connect the microphone to the
MCACC SETUP MIC
jack on the front panel.
Place the microphone so that it’s about ear level at your
normal listening position (use a tripod if possible). Make
sure there are no obstacles between the speakers and
the microphone.
The Auto MCACC display appears once the microphone
is connected.
1
3
Make sure ‘Normal (SB)’ is selected then press
ENTER.
2
4 Make sure ‘TYPE1’ is selected then press ENTER.
3
5 Follow the instructions on-screen.
Make sure the microphone is connected, and if you’re
using a subwoofer, make sure it is switched on and set to
a comfortable volume level.
6 Wait for the test tones to finish then confirm the
speaker configuration in the OSD.
A progress report is displayed on-screen while the
receiver outputs test tones to determine the speakers
present in your setup. Try to be as quiet as possible while
it’s doing this.
4
If no operations are performed for 10 seconds while the
speaker configuration check screen is being displayed,
the Auto MCACC Setup will resume automatically. In this
case, you don’t need to select ‘
OK
’ and press
ENTER
in
step 7.
• With error messages (such as
Ambient Noise
or
Microphone Check
) select
RETRY
after checking for
ambient noise (see
Problems when using the Auto
MCACC Setup
below) and verifying the mic
connection.
The configuration shown on-screen should reflect the
actual speakers you have.
5
If the speaker configuration displayed isn’t correct, use
/
to select the speaker and
/
to change the
setting (and number for surround back). When you’re
finished, go to the next step. If you see an error message
(
ERR
) in the right side column, there may be a problem
with the speaker connection. If selecting
RETRY
doesn’t
fix the problem, turn off the power and check the speaker
connections.
7 Make sure ‘OK’ is selected, then press
ENTER
.
A progress report is displayed on-screen while the
receiver outputs more test tones to determine the
optimum receiver settings for channel level, speaker
distance, and Acoustic Calibration EQ.
Again, try to be as quiet as possible while this is
happening. It may take 2 to 6 minutes.
8 The Auto MCACC Setup has finished! Select
‘SKIP’ to go back to the System Setup menu.
Be sure to disconnect the microphone from this receiver
upon completion of the Auto MCACC setup.
The settings made in the Auto MCACC Setup should give
you excellent surround sound from your system, but it is
also possible to adjust these settings manually using the
System Setup menu (starting on page 35).
6
Note
1• If you cancel the Auto MCACC Setup, or leave an error message for over three minutes, the screen saver will appear.
• The OSD will not appear if you have connected using the HDMI output to your TV. Use component, S-video, or composite connections for system setup.
2• If you are planning on bi-amping your front speakers, or setting up a separate speaker system in another room, read through
Surround back speaker
setting
on page 35 and make sure to connect your speakers as necessary before continuing to step 5.
• If you have THX-certified speakers, make sure
YES
is selected in
THX Speaker Setup
on page 42.
3 When
TYPE1
is selected, the calibration is set for
ALL CH ADJUST
; when
TYPE2
is selected, the calibration is set for both
ALL CH ADJUST
and
FRONT
ALIGN
. For details on the correction of each setting, see
Professional Acoustic Calibration EQ
on page 37.
4 Do not adjust the volume during the test tones. This may result in incorrect speaker settings.
PHONES
MCACC
SETUP MIC
DIGITAL INAUDIORLVIDEO
VIDEO/GAME
INPUT
S
-
VIDEO
SYSTEM
SETUP
TUNING/
STATIO N
TUNER
EDIT
SPEAKERSRETURN
TONE
MULTI JOG
2. Auto MCACC
Surr Back System
Normal (SB) ]
: Cancel Enter : Next
2. Auto MCACC
EQ TYPE
•
: Cancel
Enter : Start
TYPE1
• ALL CH ADJUST
5 If you’re using the front panel display, the diagram in
Listening to Surround Sound
above indicates (in bold) how each speaker is displayed.
6• Depending on the characteristics of your room, sometimes identical speakers with cone sizes of around 12 cm (5 inches) will end up with different
size settings. You can correct the setting manually using the
Manual speaker setup
on page 40.
• The subwoofer distance setting may be farther than the actual distance from the listening position. This setting should be accurate (taking delay and
room characteristics into account) and generally does not need to be changed.
2.Auto MCACC
Now Analyzing
Environment Check
Ambient Noise [ OK ]
Microphone [ ]
Speaker YES/NO [ ]
:Cancel
OK
OK
2.Auto MCACC
Check!
Front [ YES ]
Center [ YES ]
Surround [ YES ]
SB [ Yx2 ]
SUB W. [ YES ]
OK
:Cancel
10 : Next
VSX-1017TXV_KU.book 9 ページ ２００７年４月１２日 木曜日 午前１１時３２分