Filter
Top Products
Controlling the rest of your system
11
59
En
8 Repeat steps 5–7 to program a sequence of up to
five commands.
9 When you’re finished, use
/
to select EDITEXIT
from the menu and press
ENTER
.
You will return to the remote control
SETUP
menu. Select
* EXIT *
again to exit.
Using multi operations
You can start multi operations with the receiver switched
on, or in standby.
1 Press MULTI OPE.
MULTI OP
flashes in the display.
2
Press
an input source button that has been set up
with a multi operation.
The receiver switches on (if it was in standby) and the
programmed multi operation is performed automatically.
Using System off
1 Press MULTI OPE.
MULTI OP
flashes in the display.
2 Press
SOURCE
.
The command sequence you programmed will run, then
all Pioneer components will switch off
1
, followed by this
receiver.
Controls for TVs
This remote control can control components after
entering the proper codes or teaching the receiver the
commands (see
Setting the remote to control other
components
on page 57 for more on this). Use the input
source buttons to select the component.
• The
TV CONTROL
buttons on the remote control are
dedicated to control the TV assigned to the
TV CTRL
button. If you have two TVs, assign the main TV to the
TV CTRL
button.
Note
1 In order to avoid accidently switching off a DVD recorder that is currently recording, no DVD recorder power off codes are sent.
SHIFT
STEREO/
F.S.SURR
PHOTO
AUDIO
DISP
SUBTITLE
MULTI OPE
HDD
CH
CH
DVD
RECEIVER
THX STANDARD
AUTO SURR
SIGNAL SEL
ADV.SURR
ACOUSTIC EQ
EFFECT/CH SEL LEVEL
RECEIVER
SOURCE
SYSTEM OFF
INPUT
SELECT
TV DVR 1
TV CTRL
DVD
DVR 2
XM RADIO
SIRIUS
SHIFT
STEREO/
F.S.SURR
PHOTO
AUDIO
DISP
SUBTITLE
MULTI OPE
HDD
CH
CH
DVD
RECEIVER
THX STANDARD
AUTO SURR
SIGNAL SEL
ADV.SURR
ACOUSTIC EQ
EFFECT/CH SEL LEVEL
Button(s) Function Components
TV
Press to switch the component
assigned to the
TV CTRL
button on or off.
Cable TV/Satellite
TV/TV/DTV
INPUT
SELECT
Switches the TV input. (Not
possible with all models.)
Cable TV/Satellite
TV/TV/DTV
TV CH +/–
Selects channels. Cable TV/Satellite
TV/TV/DTV
TV VOL +/–
Adjust the TV volume. Cable TV/Satellite
TV/TV/DTV
SOURCE
Switches the DTV on or off. DTV
Switches the TV or CATV between
standby and on.
Cable TV/Satellite
TV/TV
Switches the DTV on or off. DTV
Press to get information on DTV
programs.
DTV
Use to choose the BLUE
commands on a DTV menu.
DTV
Use to choose the YELLOW
commands on a DTV menu.
DTV
Use to choose the GREEN
commands on a DTV menu.
DTV
Use to choose the RED
commands on a DTV menu.
DTV
AUDIO / DISP
Use to switch DTV audio tracks. DTV
SUBTITLE
Use to return to the previously
selected channel.
Cable TV/Satellite
TV/TV/DTV
GUIDE
Use as the
GUIDE
button for
navigating.
Cable TV/Satellite
TV/TV/DTV
ANT
Use to select the VHF/UHF
antennas or Cable TV.
Cable TV/TV
RETURN
Use to select
RETURN
or
EXIT
. DTV
Number
buttons
Use to select a specific TV
channel.
Cable TV/Satellite
TV/TV/DTV
+10
button Use to add a decimal point when
selecting a specific TV channel.
DTV
ENTER/
DISC
Use to enter a channel. Cable TV/Satellite
TV/TV/DTV
MENU
Select different menus from the
DTV functions.
DTV
Select the menu screen. Cable TV/Satellite
TV/TV
///
&
ENTER
Press to select or adjust and
navigate items on the menu
screen.
Cable TV/Satellite
TV/TV/DTV
VSX-1017TXV_KU.book 59 ページ ２００７年４月１２日 木曜日 午前１１時３２分