Filter
Top Products
Controlling the rest of your system
11
58
En
When direct function is on, any component you select
(using the input source buttons) will be selected by both
the receiver and the remote control. When you turn direct
function off, you can operate the remote control without
affecting the receiver.
1
1 While pressing the RECEIVER button, press
SETUP
.
The remote LCD display shows
SETUP
.
2 Use
/
to select
DIRECT F
then press
ENTER
.
The LCD on the remote prompts you for the button of the
input source you want to control.
3 Press the input source button for the component
you want to control then press
ENTER
.
4 Use
/
to switch direct function ON or OFF then
press
ENTER
.
The LCD shows
OK
to confirm the setting.
Multi Operation and System Off
The Multi Operation feature allows you to program a
series of up to five commands for the components in your
system. For example, you could turn on your TV, turn on
your DVD player and start playing the loaded DVD using
only two buttons on the remote control.
Similar to multi operations, System Off allows you to use
one button to stop and switch off a series of components
in your system at the same time.
2
Programming a multi-operation or a
shutdown sequence
1 While pressing the RECEIVER button, press
SETUP
.
The remote LCD display shows
SETUP
.
2 Use
/
to select MULTI OP or SYS OFF from the
menu and press
ENTER
.
If you selected Multi Operation
(
MULTI OP
), the LCD on
the remote prompts you for an input source button.
If you selected System Off
(
SYSOFF
), go to step 4.
3 Press the input source button for the component
that will start the multi-operation then press
ENTER
.
For example, if you want to start the sequence by
switching on your DVD player, press
DVD
.
4 Use
/
to select CODE EDT then press
ENTER
.
To erase any previously stored multi-operations (or
shutdown sequences) select
CODE ERS
above.
5 Use
/
to select a command in the sequence then
press
ENTER
.
If this is the first command in the sequence, select
1ST
CODE
. Otherwise, simply choose the next command in
the sequence.
PRES KEY
flashes after you press
ENTER
.
6 If necessary, press the input source button for the
component whose command you want to input.
This is only necessary if the command is for a new
component (input source).
7 Select the button for the command you want to
input.
The following remote control commands can be selected:
• You don’t need to program the receiver to switch on
or off. This is done automatically.
With Pioneer components
, you don’t need to:
• program the power to switch off in a shutdown
sequence (except DVD recorders);
• program the power to switch on if it’s the source
component selected in step 3;
• program a Pioneer TV or monitor to switch on if the
input function (selected in step 2) has video input
terminals;
These take priority in multi operations (not shutdown).
Note
1 You can’t use direct function with the
TV CTRL
function.
2• Before Multi Operation and System Off will work correctly, you must setup the remote to work with your TV and other components (see
Setting the
remote to control other components
on page 57 for more on this).
• Some units may take some time to power up, in which case multiple operations may not be possible.
• Power on and off commands only work with components that have a standby mode.
ANALOG
AT T
SLEEP SB ch
TV DVR 1
TV CTRL
CD
RECEIVER
TUNERiPod
DVD
CD-R/TAPE
DVR 2
XM RADIO
SIRIUS
ENTER
TV CONTROL
TUNE
TUNE
ST ST
TOP MENU
T. EDIT
MENU
RETURN
GUIDE
BAND
SETUP
ANALOG
AT T
MIDNIGHT/
LOUDNESS
DIMMER
SLEEP SB ch
SR+
+10
D.ACCESS
DIALOG E PHASE
S.RETRIEVER
CLASS
DISC
RECEIVER
SOURCE
SYSTEM OFF
INPUT
SELECT
ENTER
TUNE
TUNE
ST ST
ENTER
TOP MENU
T. EDIT
MENU
RETURN
GUIDE
BAND
SETUP
TV DVR 1
TV CTRL
CD
RECEIVER
TUNERiPod
DVD
CD-R/TAPE
DVR 2
XM RADIO
SIRIUS
TV CONTROL
SHIFT
VOL
STEREO/
F.S.SURR
PHOTO
INPUT
SELECT
TV CH
MPX
AUDIO
DISP
SUBTITLE
MULTI OPE
RECANT INFO
MUTE
TV VOL
REC STOP JUKEBOX
HDD
CH
CH
DVD
RECEIVER
THX STANDARD
AUTO SURR
SIGNAL SEL
ADV.SURR
ACOUSTIC EQ
EFFECT/CH SEL LEVEL
VSX-1017TXV_KU.book 58 ページ ２００７年４月１２日 木曜日 午前１１時３２分