Filter
Top Products
18
RQTX1267
You can select the sound input level of the Bluetooth
®
device.
1 Press [ , iPod] repeatedly to select
“BLUETOOTH”.
2 Press [SOUND] repeatedly to select “INPUT
LEVEL”.
3 Press [2, 1] to select “0”, “i1” or “i2”.
≥ Select “0” if the sound is distorted.
Press [DISPLAY] repeatedly to view the
information of the current connected device.
BLUETOOTH ---------------------# Connected device name
^-------------------------- Connected profiles(------------------------}
This unit works as a Bluetooth
®
hands-free for your mobile
phones.
≥ This unit does not work with Headset Profile (HSP).
≥ When the mobile phone is too close to the microphone of this unit, noise may
occur. Always keep the mobile phone away from the microphone of this unit
when making a call.
≥ The audio from a disc will be paused while calling in hands-free mode.
1 Press [ , iPod] repeatedly to select
“BLUETOOTH”.
2 Press [ MENU] to display “DISCONNECT?”
and then press [OK].
A confirmation message is displayed.
3 Press [2, 1] to select “YES” and then press
[OK].
≥ The connection can also be stopped when you disable Bluetooth
®
transmission on the connected Bluetooth
®
device.
Preparation
Press [ , iPod] repeatedly to select “BLUETOOTH”.
≥ These functions are unavailable if a device is connected. Disconnect the
Bluetooth
®
devices to display these functions.
∫ To register more devices
1 Press [ MENU] repeatedly to select
“NEW DEV.” and then press [OK].
≥ The unit enters pairing mode and “PAIRING” starts blinking
on the display.
2 While this unit is in pairing mode, access the
Bluetooth
®
menu of the Bluetooth
®
device and
execute a Bluetooth
®
search to find this unit
(SC-HC55).
≥ If prompted for the passkey, enter “0000”.
∫ To select communication quality
1 Press [ MENU] repeatedly to select
“LINK MODE”.
2 Press [2, 1] to select the following modes and
then press [OK].
∫ To select Auto Link mode
1 Press [ MENU] repeatedly to select
“AUTO LINK”.
2 Press [2, 1] to select the following modes and
then press [OK].
≥ When “LINKING” is displayed, pressing [ MENU] is invalid.
≥ Auto Link works only if your device supports A2DP.
≥ The communication quality settings also depend on the settings on the
connected device. If the communication quality of the connected device is set
for stable communication, the quality of the audio will remain low even if this
unit is set to “MODE 2”.
Input level
Display function
Hands-Free Profile (HFP)
To answer a call
(“IN CALL” blinks)
Press [ ]. “CALLING” starts blinking on
the display (Talk into the unit’s
microphone).
Press [ ] again to transfer the call to the
mobile phones (“TRANSFER” blinks. You
may now converse using the mobile
phone).
To cancel a call Press [ ].
To adjust the
sound volume
Press [+, VOL ,–] (Adjustable from
“TEL VOL 1” to “TEL VOL 10”).
To mute the
microphone
Press [MUTE]. Press again to cancel.
(During “MIC MUTE”, the caller is not able
to hear your voice).
Disconnecting a Bluetooth
®
device
Advanced functions
MODE 1: Connection with emphasis on communication
stability
MODE 2: Connection with high bit rate for good audio quality
(Communication might easily be disconnected in
this mode, select “MODE 1” if this occurs).
ON: This unit will automatically select “BLUETOOTH”
when a Bluetooth
®
device is connected.
OFF
SC-HC55DB&35GN-RQTX1267-B.book 18 ページ ２０１１年２月１８日 金曜日 午後５時５８分