Filter
Top Products
49
RQT9223
Listening to the Radio
Operations
Manual tuning
“TUNED” is displayed when a station is tuned.
“ST” is displayed when a stereo FM broadcast is tuned.
Tuning directly using the numbered
buttons
1. Press [FM/AM] to activate the radio.
2. Press [FM/AM] to select “FM ” or “AM ”.
3.
Press [DIRECT TUNING, DISC] to select
Direct Tuning Mode.
4. Press the numbered buttons to enter the
frequency.
e.g. FM 107.9 MHz,
Press [DIRECT TUNING, DISC]
→
[1]
→
[0]
→
[7]
→
[9].
• If y
ou do not press a button while the cursor is flashing, the
display returns to the frequency being received.
• If the frequency has not been input correctly, “ERROR ” will be
displa
yed.
Using the unit
1. Turn [INPUT SELECTOR] to select “FM ”
or
“AM ”.
2.
Press [TUNE
2
or
1
] to tune in a station.
Using the remote control
1. Press [FM/AM] to select “FM ” or “AM ”.
2.
Press [
t
] [
y
] to tune in a station.
g
Automatic tuning
Hold down [TUNE
2
or
1
] on the unit or [
t
] [
y
] on the
remote control until the frequency begins to scroll.
• Tuning stops when a station is found.
• Tuning may stop if there is interference.
Note
• To cancel during auto tuning, press [TUNE
2
or
1
] on the unit
or [
t
] [
y
] on the remote control.
Reducing excessive noise
During FM stereo reception
You can improve FM reception by switching reception to
monaural.
1. To enter the SETUP (
➔
pa
ge 36)
2. Press [
e
][
r
] to select
“TUNER ”, and
press [OK] to confirm.
3.
Press [
e
][
r
] to select
“FM MODE ”, and
press [OK] to confirm.
4.
Press [
e
][
r
] to select
“MONO ”, and
press [OK] to confirm.
• When this is set, “MONO” appears on the display.
• Select “AUTO ” to cancel.
5. To finish the setting (
➔
pa
ge 36)
During AM reception
When there is a lot of noise interference with an AM broadcast,
try switching to this mode.
1. To enter the SETUP (
➔
pa
ge 36)
2. Press [
e
][
r
] to select
“TUNER ”, and
press [OK] to confirm.
3.
Press [
e
][
r
] to select
“BEAT PROOF ”,
and press [OK] to confirm.
4. Press [
e
][
r
] to select
“MODE 1 ” or
“MODE 2 ”, and press [OK] to confirm.
Factory setting: MODE 1
5. To finish the setting (
➔
pa
ge 36)
• Select “MODE 1 ” or “MODE 2 ” according to the improvement
of sound.
FM frequency step
If the correct FM frequency cannot be tuned in, change the
frequency step to suit your area.
1. To enter the SETUP (
➔
pa
ge 36)
2. Press [
e
][
r
] to select
“TUNER ”, and
press [OK] to confirm.
3.
Press [
e
][
r
] to select
“FM STEP ”, and
press [OK] to confirm.
4.
Press [
e
][
r
] to select
“100 ” or “200 ”,
and press [OK] to confirm.
Factory setting: 200kHz
5. To finish the setting (
➔
pa
ge 36)
• When the frequency step is changed, the previously
memorized preset stations are initialised to the settings made
at the time of shipment.
Note
Note
SA-BX500-PP (RQT9223-Y)_En.indd 49 6/27/2008 4:06:45 PM