Filter
Top Products
36
VQT3M40
Optional speaker settings
Speaker installation
option
You can attach all of the speakers (except subwoofer) to a wall.
≥ The wall or pillar on which the speakers are to be attached
should be capable of supporting 10 kg (22 lbs) per screw.
Consult a qualified building contractor when attaching the
speakers to a wall. Improper attachment may result in
damage to the wall and speakers.
≥ Do not attempt to attach these speakers to walls using
methods other than those described in this manual.
1 Drive a screw (not supplied) into the wall.
2 Fit the speaker securely onto the screw(s)
with the hole(s).
Use the measurements indicated below to identify the
screwing positions on the wall.
≥ Leave at least 20 mm (
25
/32q) of space above the speaker and
10 mm (
13
/32q) on each side to allow enough space for fitting
the speaker.
Front speaker,
Surround speaker
F 40 mm (1
9
/16q)
G 17.6 mm (
11
/16q)
H 98.7 mm (3
7
/8q)
Center speaker
I 23 mm (
29
/32q)
J 95 mm to 97 mm
(3
3
/4q to 3
13
/16q)
K 26 mm (1
1
/32q)
L 16.7 mm (
21
/32q)
M 63.7 mm (2
1
/2q)
Reference
Troubleshooting guide
Before requesting service, please perform the
following steps.
The following do not indicate a problem with this unit:
jRegular disc rotating sounds.
jImage disturbance during search.
jImage disturbance when replacing 3D discs.
∫ Unit does not respond to the remote
control or front panel buttons.
Press and hold [POWER Í/I] on the main unit for 5 seconds.
jIf still unable to power the unit off, disconnect the power cord,
wait 1 minute, then reconnect the power cord.
∫ Cannot eject disc.
The unit may have a problem.
While the unit is off, press and hold [9] on the remote
control and [< OPEN/CLOSE] on the unit at the same time for
more than 5 seconds.
To return to the factory preset
≥ Select “Yes” in “Restore Default Settings” in the Setup menu.
( 34)
To return all settings to the factory preset
≥ Reset the unit as follows:
While the unit is off, press and hold [+ VOLUME], [< OPEN/
CLOSE] and [POWER Í/I] on the main unit at the same
time for more than 5 seconds.
The remote control doesn’t work properly.
≥ Change the batteries in the remote control. ( 9)
≥ The remote control and main unit are using different codes. If
“SET ” is displayed on the unit’s display when a button is
pressed on the remote control, change the code on the
remote control. ( 34)
Disc cannot be played.
≥ The disc is dirty. ( 9)
≥ Check the region code.
Attaching to a wall
A At least 30 mm (1
3
/16q)
B ‰ 4.0 mm (
5
/32q)
C ‰ 7.0 mm to ‰ 9.4 mm
(
9
/32q to
3
/8q)
D Wall or pillar
E 5.5 mm to 7.5 mm
(
7
/32q to
5
/16q)
e.g., Front speaker
DO NOT DO
≥ In this position, the
speaker will likely fall if
moved to the left or right.
≥ Move the speaker so that
the screw is in this
position.
Do you have the latest firmware installed?
Firmware updates may be released to correct operating
irregularities that are discovered with certain movies. ( 17)
4
Make the following checks and visit our
website for more information.
http://www.panasonic.com/help
Enter the model number.
4
Or visit our website to find a service
center.
You can find a service center near you easily on our website.
Other support information:
“Customer Services Directory (United States and Puerto
Rico)” ( 43)
General operation
SC-BTT268_P_eng.book 36 ページ ２０１０年１２月２４日 金曜日 午前１１時１９分