Filter
Top Products
16
RQT7994
ConnectionsSettingsBasic OperationsOperations Before useReference
Control guide
• DIGITAL EX and EX are displayed only when “1 SPKR ” is selected in “Surround back speaker settings”. (ápage 12)
•
PL
is displayed when using Dolby Pro Logic with stereo (2-channel) sources and “
SB
” is set to “
_
” in “Speakers combination settings”. (
á
page 12)
Main unit
[8, POWER]
Press to switch the unit from on to standby mode
or vice versa. In standby mode, the unit is still
consuming a small amount of power.
Standby indicator [^]
When the unit is connected to the AC mains
supply, this indicator lights up in standby mode
and goes out when the unit is turned on.
[SPEAKERS, A, B]
For selecting speakers A or B.
Turning the speakers off
automatically engages the
STEREO/2CH MIX mode (when
listening through headphones, for
example).
[MULTI CONTROL, CANCEL]
Press to enter Multi control or cancel.
[ENTER]
Enters setting in Multi control.
[INPUT SELECTOR]
For selecting input.
Selects each setting in Multi control.
[VOLUME]
Volume
control.
Remote
control signal
sensor
[VCR 2]
For a game player,
etc.
[DUAL AMP]
Lights when the
DUAL AMP function
is activated.
[BI-AMP]
Lights when the BI-
AMP function is
activated.
[BAND]
For switching between FM and AM.
[PRESET]
Press to allow preset station selection with [2 TUNE 1].
[2 TUNE 1]
For tuning the radio and selecting preset stations.
Press and hold until the frequency starts scrolling to start
automatic tuning. Tuning stops when a station is found.
[PHONES]
Headphone jack.
Plug type: 6.3 mm (1/4") stereo
Avoid listening for prolonged
periods of time to prevent hearing
damage.
Turn the speakers off when using
the headphones.
Display indicators
[RE-MASTER]
Lights when the multi-source
re-master function is on.
[MULTI CONTROL]
When you press the [MULTI
CONTROL, CANCEL] button
and enter the settings the
indicator lights.
[SLEEP]
Sleep timer indicator.
[TUNED]
A station is tuned.
[ST]
A stereo FM broadcast is tuned.
[MONO]
Lights when using the monaural
mode.
[]
Flashes during automatic
presetting.
[DIGITAL INPUT]
• The channels contained in the digital input signal light.
• No sound is output from a channel if the speaker is set to “
_
” (not connected) in
“Speakers combination settings” (
á
page 12) even if the channel indicator lights.
L: Front left channel C: Center channel
R: Front right channel LS: Surround left channel
SB: Surround back channel RS: Surround right channel
S: If the surround channel is monaural
LFE (Low Frequency Effects): Deep-bass effect
[PCM]
Lights when the PCM FIX mode is set.
[– SPEAKERS – , , ]
Speaker indicators.
General
display
Shows the input
mode, radio
frequency, and
other general
information.
[2CH MIX]
Lights when playing a
multi-channel source in
2CH MIX mode.
[kHz, MHz]
Frequency unit indicators.
kHz:
AM, or PCM sampling
frequency
MHz:FM
[SOUND MODE]
The following light to
indicate the source’s
input signal (multi-
channel digital signal)
and the decoding
format used.
(
á
below)
A: Sound is output from speakers connected to the
front A, surround, and center terminals.
B: Sound is output only from speakers connected to
the front B terminals.
A, B: Sound is output from speakers connected to the
front A, B, surround, and center terminals.
A, B, BI-WIRE:
Sound is output from speakers connected by Bi-wiring.
SOUND MODE
DIGITAL:
DIGITAL EX:
EX:
DTS-ES:
DTS:
DTS 96/24:
STEREO:
Dolby Digital decoder is being used.
Dolby Digital Surround EX decoder (Dolby Pro Logic decoder) is being used when
the input signal is Dolby Digital 5.1-channel or Dolby Digital Surround EX.
Dolby Digital Surround EX decoder (Dolby Pro Logic decoder) is being used when the input signal is DTS.
DTS-ES discrete or matrix decoder is being used.
DTS decoder is being used.
DTS 96/24 decoder is being used.
2-channel stereo decoder is being used.
PL :
PL :
NEO:6:
SFC:
Dolby Pro Logic
decoder is being used.
Dolby Pro Logic
decoder is being used.
DTS NEO:6 matrix
decoder is being used.
SFC matrix function is
being used.