Filter
Top Products
113
Troubleshooting—Continued
Can’t control other components
• If it’s an Onkyo component, make sure that the
cable and analog audio cable are connected properly.
Connecting only an cable won’t work (page 43).
• Make sure you’ve selected the correct remote control-
ler mode (pages 15-19).
• If you’ve connected an -capable Onkyo MD
recorder, CD recorder, Dock to the TAPE IN/
OUT jacks, or an Dock to the GAME/TV IN
jacks, for the remote controller to work properly, you
must set the display to MD, CDR, or DOCK (page
50).
When operating a DS-A1 RI Dock, enter the appropri-
ate remote control code for the first time (page 104).
• To control another manufacturer’s component, point
the remote controller at that component.
• To control an Onkyo component that’s connected via
, point the remote controller at the AV receiver/AV
amplifier. Be sure to enter the appropriate remote con-
trol code first (page 105).
• To control an Onkyo component that’s not connected
via , or another manufacturer’s component, point
the remote controller at the component. Be sure to enter
the appropriate remote control code first (page 104).
Can’t record
• On your recorder, make sure the correct input is
selected (e.g., digital or analog).
• When the Pure Audio listening mode is selected, record-
ing is not possible because no video signals are output.
Select another listening mode.
There’s no sound
• Only components connected to analog inputs can be
played in Zone 2.
The sound changes when I connect my head-
phones
• When a pair of headphones is connected, the listening
mode is set to Stereo, unless it’s already set to Stereo,
Mono, Direct, or Pure Audio.
The speaker volume cannot be set as required
• When the Automatic Speaker Setup function is used,
or the volume is adjusted on the onscreen setup
menus, the maximum possible volume setting may
change.
The speaker distance cannot be set as required
• In some cases, corrected values suitable for home the-
ater use may be set automatically.
The display doesn’t work
• The display is turned off when the Pure Audio (not
North American models) listening mode is selected.
How do I change the language of a multiplex
source
• Use the “Multiplex” setting on the “Audio Adjust”
menu to select Main or Sub (page 85).
The functions don’t work
• To use , you must make an connection and an
analog audio connection (RCA) between the compo-
nent and AV receiver/AV amplifier, even if they are
connected digitally (page 43).
The functions Auto Power On/Standby and
Direct Change don’t work for components con-
nected via
• These functions don’t work when Zone 2 is turned on.
When performing “Automatic Speaker Setup,”
the measurement fails showing the message
“Ambient noise is too high.”
• This can be caused by any malfunction in your speaker
unit. Check if the unit produces normal sounds.
The following settings can be made for the S-Video
and composite video inputs
You must use the buttons on the unit to make these set-
tings.
1. While holding down the input selector button for the
input source that you want to set, press the [SETUP]
button.
2. Use the Left and Right [ ]/[ ] buttons to change
the setting.
3. Press the [SETUP] button when you’ve finished.
• Video Attenuation
This setting can be made for the DVD, VCR/DVR,
CBL/SAT, GAME/TV, or AUX input.
If you have a games console connected to the
S-Video or composite video input, and the picture
isn’t very clear, you can attenuate the gain.
Video ATT:0: (default).
Video ATT:2: Gain is reduced by 2 dB.
Recording
Zone 2
Others
The AV receiver/AV amplifier contains a microcomputer
for signal processing and control functions. In very rare
situations, severe interference, noise from an external
source, or static electricity may cause it to lockup. In the
unlikely event that this happens, unplug the power cord
from the wall outlet, wait at least five seconds, and then
plug it back in again.
Onkyo is not responsible for damages (such as CD
rental fees) due to unsuccessful recordings caused by
the unit’s malfunction. Before you record important
data, make sure that the material will be recorded cor-
rectly.
Before disconnecting the power cord from the wall out-
let, set the AV receiver/AV amplifier to Standby.
TX-SR705_En.book Page 113 Thursday, May 31, 2007 5:00 PM