Filter
Top Products
59
Using the Listening Modes—Continued
The TX-NR1000/TX-NR5000E provides various listen-
ing modes.
Note:
The available modes depend on the input signal you
selected.
Operating on the TX-NR1000/TX-NR5000E
Operating with the Remote Controller
Tip:
A table listed later in this manual shows which listening
mode can be used with which input signal format. See
page 143.
Selecting the Listening Mode
1
Press the input source button.
2
Start playback on the device you selected
for input.
3
Press the [LISTENING MODE] button, and
then turn the [SELECT/PRESET] to select
a listening mode.
1
Roll the scroll wheel to select a device for
playback.
Perform this operation when neither the [MODE]
button nor the [INPUT] button lights. If any but-
ton lights, press it to turn it off.
Rolling the scroll wheel lights both buttons, and
switches the input source and the mode at the
same time.
STANDBY/ON
STANDBY
PURE AUDIO
MASTER VOLUME
OPEN
ZONE 2
()
GREEN
MAIN
()
BLUE
REC
/
ZONE 3
(
)
RED
DISPLAY
DVD
VIDEO
3
VIDEO 4 VIDEO 5 VIDEO 6 VIDEO 7VIDEO 2VIDEO 1
MEMORY
SETUP
EXIT
PHONES
VIDEO 7 INPUT
S VIDEO
DIGITAL
AUDIO
VIDEO L R
LISTENING
MODE
AUDIO
SELECTOR
TONE
CLEAR
DIMMER
ZONE
2 REC/
ZONE 3
LEVEL LEVEL
SELECT/
PRESET
CONTROL
/
TUNING
PUSH TO ENTERPUSH TO ENTER
C
D NET AUDIOPHONOTUNERTAPE 1 TAPE 2
TUNING
MODE
--
/
---
@.
-
'
/ ABC DEF
PQRS TUV WXYZ
DIRECT TUNING
GHI JKL MNO
CAPS DELETE
LANGUAGE LOCATION
ALBUM AR
TIST GENRE
PLAYLIST
REPEAT VIDEO MUSIC PHOTO
CUSTOM
DISPLAY
DIMMER
T
V
INPUT
SLEEP
RANDOMREC
MAIN A MAIN B
MUTING
ENTER
LAST MANGLE
SUBTITLE
AUDIO
MEMORY
SEARCHA
-
BREPEAT
ON STANDBY
TV
TV CH
TV VOL
S
E
R
V
E
R
A
U
D
I
O
A
D
J
E
X
I
T
G
U
I
D
E
PREV
CH
+
10 0
CLEAR
123
456
789
INPUT
T
O
P
M
E
N
U
M
E
N
U
S
E
T
U
P
R
E
T
U
R
N
ZONE
2
INPUTMODE
MACRO
VOL
CH
DISC
TEST T
O
NE
CH SEL
PURE A
SURR
DIRECT
STEREO
Re
-
EQ
THX
A
LL
ST
LEVEL
+
LEVEL
-
L NIGHT
AUDIO
SEL
DSP DSP
+
-
+
-
I
ZONE
3
#
MODE
SELECT/PRESETLISTENING MODE
SURR
THX
STEREO
ALL ST
DIRECT
PURE A
DSP
DSP
INPUT
Input source buttons
Scroll wheel
RC-557M
RC-558M
2
Start playback on the device you selected
for input.
3
Press the scroll wheel, and then press the
listening mode button you want to select.
PURE A button: To switch the listening mode to
“Pure Audio.” When you select “PURE AUDIO,”
the video signal is interrupted (resulting in a
blacked-out screen), and the [PURE AUDIO]
indicator lights up.
DIRECT button: To switch the listening mode
to “Direct.”
STEREO button: To switch the listening mode
to “Stereo.”
SURR button: To switch the listening mode to
the surround mode.
• When 5 channel signals are input, every time
you press the button, the listening mode
changes “DolbyEX” →
“PLIIx Movie
(Default)” →
“PLIIx Music” → “NEO:6”→
“Off” → “DolbyEX,” and so on.
• When 2 channel signals are input, every time
you press the button, the listening mode
changes “PLIIx Movie (Default)” → “PLIIx
Music” → “PLIIx Game” → “NEO:6 Cinema”
→ “NEO:6 Music”→ “PLIIx Movie
(Default),” and so on.
THX button: To switch the listening mode to
“THX.”
• When Dolby Digital multichannel (*/2) signals
are input, you can switch to any of the following
decode modes. Every time you press the button,
the listening mode changes “THX Cinema” →
“SurroundEX” → “Ultra2 Cinema (Default)” →
“MusicMode” → “Games Mode”→“THX Cin-
ema,” and so on (See page 112).
DSP/DSP buttons: Every time you press
the buttons, you can switch to any of the listening
modes according to the input signals.
ALL ST button: To switch the listening mode to
“All Ch Stereo.”
[ ]/[ ] cursor buttons:
• When AAC’s multiplex sound signals are
input, the main-sound and sub-sound are
switched. Every time you press the [ ]/[ ]
buttons, the mode changes “Main” →
“Sub”
→
“Main + Sub” → “Main,” and so on.
• When using the headphones, you can use the
[ ]/[ ] buttons to switch on/off the Dolby
Headphone listening mode.