Filter
Top Products
50
Connecting the Power/Basic Operations
• Before you plug in the TX-NR1000/TX-NR5000E, confirm that all connections have been made properly.
• Turning on the power may cause a momentary power surge, which might interfere with other electrical equipment
on the same circuit, such as computers. If this happens, use a wall outlet on a different circuit.
(All models other than USA, Canadian, and Australian models)
The TX-NR1000/TX-NR5000E is shipped with the main power (POWER) switch in the on position ( ). When
the power cord is plugged in for the first time, the TX-NR1000/TX-NR5000E will automatically enter the standby
state and the [STANDBY] indicator will light (same condition after step 2 below on the left column).
Note:
Any components connected via will also be turned
on when the remote controller’s [ON] button is pressed.
ON
STANDBY/ON
STANDBY
PURE AUDIO
MASTER VOLUME
OPEN
ZONE 2
()
GREEN
MAIN
()
BLUE
REC
/
ZONE 3
(
)
RED
DISPLAY
DVD
VIDEO
3
VIDEO 4 VIDEO 5 VIDEO 6 VIDEO 7VIDEO 2VIDEO 1
MEMORY
SETUP
EXIT
PHONES
VIDEO 7 INPUT
S VIDEO
DIGITAL
AUDIO
VIDEO L R
LISTENING
MODE
AUDIO
SELECTOR
TONE
CLEAR
DIMMER
ZONE
2 REC/
ZONE 3
LEVEL LEVEL
SELECT/
PRESET
CONTROL
/
TUNING
PUSH TO ENTERPUSH TO ENTER
C
D NET AUDIOPHONOTUNERTAPE 1 TAPE 2
TUNING
MODE
OFF
ON
STANDBY/ON
STANDBY
PURE AUDIO
MASTER VOLUME
POWER
OPEN
ZONE 2
()
GREEN
MAIN
()
BLUE
REC
/
ZONE 3
(
)
RED
DISPLAY
DVD
VIDEO
3
VIDEO 4 VIDEO 5 VIDEO 6 VIDEO 7VIDEO 2VIDEO 1
MEMORY
SETUP
EXIT
PHONES
VIDEO 7 INPUT
S VIDEO
DIGITAL
AUDIO
VIDEO L R
LISTENING
MODE
AUDIO
SELECTOR
TONE
CLEAR
RT/
PTY/
TP
ZONE
2 REC/
ZONE 3
LEVEL LEVEL
SELECT/
PRESET
CONTROL
/
TUNING
PUSH TO ENTER
PUSH TO ENTER
C
D NET AUDIOPHONOTUNERTAPE 1 TAPE 2
TUNING
MODE
STANDBY/ON
POWER
MASTER VOLUME
STANDBY/ON
MASTER VOLUME
(USA, Canadian, and Australian models) (Other models)
STANDBY indicator
Input source buttons
To wall outlet
Input source buttons
STANDBY indicator
To wall outlet
Turning on the Power
1
Plug the power cord into an AC
wall outlet.
(USA, Canadian, and Australian
models)
The [STANDBY] indicator will light up.
(Other models)
Press the [POWER] switch to set
the TX-NR1000/TX-NR5000E to
standby state.
The [STANDBY] indicator will light up.
2
Press the [STANDBY/ON] button to
turn on the TX-NR1000/
TX-NR5000E.
The display will light up and the
[STANDBY] indicator will turn off.
If you press the [STANDBY/ON] button
again, the TX-NR1000/TX-NR5000E
returns to the standby state.
OFF
ON
STANDBY
POWER
STANDBY/ON
STANDBY
Turn off
Operating on the TX-NR1000/
TX-NR5000E
1
Select an input source.
Press the input source button.
*You cannot listen to a source in main
room A, and to another source in main
room B.
2
Start playing the device selected.
When playing a picture device such as a
DVD player, you need to switch input to
a monitor such as a TV set.
Some picture-playing devices such as a
DVD-type game machine may also
require setting of sound output. Refer to
the manual of the device connected.
3
Adjust the volume level with the
[MASTER VOLUME] dial.
You can adjust the volume level in the
range from –∞, –81.5 dB to 18.0 dB
(Max) (when Relative is selected in the
Volume Setup sub-menu).
Hint:
TX-NR1000/TX-NR5000E is a product
for users to enjoy home theater, so it is
equipped with a wide range of volume
levels. Please fine tune the volume level
according to your preferences.
TAPE 1 TAPE 2
VIDEO
4 VIDEO 5 VIDEO 6 VIDEO 7
DVD
VIDEO
3
VIDEO 2VIDEO 1
C
D NET AUDIOPHONOTUNER
MASTER VOLUME