Onkyo TX-SR601E Stereo Receiver User Manual


 
61
Recording
STANDBY/ON
PHONES
VIDEO 4
INPUT
DIGITAL
VIDEO 3
TAPE
VIDEO
4
SURROUND THX DSP
STEREO
STANDBY
DISPLAY
VIDEO 2
DVD
VIDEO
1
AUDIO
SELECTOR
LISTENING MODE
MASTER VOLUME
RETURN
ENTER
AUDIO
ADJUST
SETUP
RT/PTY/TP
VCR 2VCR 1
S VIDEO
VIDEO
AUDIO
LR
OFF
ON
POWER
TUNER CD
PHONO
DIRECT/
PURE AUDIO
PURE AUDIO
REC OUT ZONE 2
OFF
LEVEL
MEMORY
CLEAR
FM MODE
PRESET
TUNI
NG
REC OUT OFF
Input source buttons
Notes:
You cannot record the surround effects.
Digital signals input to the DIGITAL INPUT (COAXIAL) and
DIGITAL INPUT (OPTICAL) inputs will be output to the
DIGITAL OUTPUT (COAXIAL) and DIGITAL OUTPUT
(OPTICAL) output.
There are some restrictions on recording digital signals. When
making digital recordings, consult the instruction manual that
came with your digital recording equipment (e.g., MD recorder
or DAT deck) to know what restrictions are imposed.
You cannot record the source connected to the 5.1-channel input
jacks.
If you change the input source during recording, you will record
the signals from the newly selected input source.
Digital input signals are only output to the digital outputs and
analog input signals are only output to the analog outputs. There
is no conversion from digital to analog or vice versa. When
connecting CD players and other digital components, do not
connect only the digital terminals, but the analog ones as well.
When using the TX-SR701/701E/601/601E to record a source, you
must select that source to be output from the TAPE OUT jacks.
Recording the same source that you are listening to:
1. Press the input source button for the source that you
want to record.
2. Press the REC OUT button repeatedly
until “Rec Sel : SOURCE” appears in
the front display.
3. Start recording at the recording device connected to
the TAPE OUT jacks.
Recording the input source (REC OUT selector)
VIDEO 3
TAPE
VIDEO
4
VIDEO 2
DVD
VIDEO
1
VCR 2VCR 1
TUNER CD
PHONO
Note:
Be aware that if you change the input source that you are watching
(or listening to), the selected source will be recorded.
Recording a source different from that you are listening
to:
The TX-SR701/701E/601/601E allows you to listen to one
source while recording the signal from another source. The
procedure below uses the example of recording the audio from a
CD player while watching the input from a DVD player.
1. While playing the DVD, press the
REC OUT button.
2. Within 5 seconds, press the input source button of
the source that you wish to record.
In this example you would press the CD source button. The
signal from the CD player is now output to the TAPE OUT
jacks.
3. Start recording at the recording device connected to
the TAPE OUT jacks.
You can press the REC OUT button to display which input
source is selected for recording. When “Rec Sel: Off” is
displayed, no signal is output for recording.
To confirm the settings, press the REC OUT button. The current
settings will appear for 5 seconds in the front display.
To turn off the Rec Out, press the REC OUT button and then
press the OFF button within five seconds.
Notes:
You cannot use the REC OUT selector to record video signals.
Be aware that the ZONE 2 and REC OUT selectors use the
same circuit and therefore cannot be used at the same time.
Even if you change the input source that you are listening to, the
input source that is selected for recording will not change.
However, if you have selected FM (or AM) as the source to be
recorded and the AM (or FM) source button is pressed, the
source being recorded will be changed to the AM (or FM) input
signal.
VIDEO 3
TAPE
VIDEO
4
VIDEO 2
DVD
VIDEO
1
VCR 2VCR 1
TUNER CD
PHONO