Filter
Top Products
Advanced Operations
En-56
■ PL IIz Height Gain
`Low
`Mid
`High
The Height Gain Control in Dolby Pro Logic IIz enables
the listener to select how much gain is applied to the front
high speakers. There are three settings, “Low”, “Mid” and
“High”, and the front high speakers are accentuated in that
order. While “Mid” is the default listening setting, the
listener may adjust the Height Gain Control to their
personal preference.
Note
• If the “Front High” setting is set to “None” (➔ page 52), this
setting cannot be selected.
• If the “Powered Zone 2” setting is set to “Yes” (➔ page 52)
and Zone 2 is turned on, this setting cannot be selected.
■ Dolby EX
`Auto:
If the source signal contains a Dolby EX flag, the
Dolby EX or THX Surround EX listening mode is
used.
`Manual
:
You can select any available listening mode.
This setting determines how Dolby EX encoded signals are
handled. This setting is unavailable if no surround back
speakers are connected. This setting is effective with
Dolby Digital, Dolby Digital Plus and Dolby TrueHD only.
Note
• If the “Surround Back” setting is set to “None” (➔ page 52),
this setting cannot be selected.
• If the “Powered Zone 2” setting is set to “Yes” (➔ page 52)
and Zone 2 is turned on, this setting cannot be selected.
■ TrueHD Loudness Management
`Off
`On
This setting specifies whether or not to apply the Late
Night processing on a Dolby TrueHD source.
Note
• When this setting is set to “Off”, the Late Night function for
Dolby TrueHD sources is automatically fixed to “Off”
(➔ page 47).
• When this setting is set to “Off”, the Dialogue Normalization
information is not available for Dolby TrueHD sources.
DTS
■ Neo:6 Music
Center Image
`0 to 2
to 5
The DTS Neo:6 Music listening mode creates 6-channel
surround sound from 2-channel stereo sources. With this
setting, you can specify by how much the front left and
right channel output is attenuated in order to create the
center channel.
Changing the value from “0” to “5” will spread the sound
of the center channel to left and right (outwards).
Audyssey DSX
®
■ Soundstage
`–3dB to Reference
to +3dB
With this setting, you can adjust the sound stage when using
Audyssey DSX.
Note
• This listening mode can be selected only when all the following
conditions are satisfied:
– The center speaker is connected.
– The front high speakers are connected.
– Powered Zone 2 is not in use.
Theater-Dimensional
■ Listening Angle
`Wide
:
Select if the listening angle is greater than 30 degrees.
`Narrow:
Select if the listening angle is less than 30 degrees.
With this setting, you can optimize the Theater-
Dimensional listening mode by specifying the angle of the
front left and right speakers relative to the listening
position. Ideally, the front left and right speakers should be
equidistant from the listening position and at an angle close
to one of the two available settings.
Note
• For best results, we recommend setting “
Narrow” to 20° and
“Wide” to 40°.
LFE Level
■ Dolby Digital
*1
, DTS
*2
, Multich PCM, Dolby
TrueHD, DTS-HD Master Audio, DSD
*3
`– dB, –20dB, –10dB, or 0dB
With these settings, you can set the level of the LFE (Low
Frequency Effects) channel individually for each input
sources.
If you find that low-frequency effects are too loud when
using one of these sources, change the setting to –20 dB or
– dB.
*1
Dolby Digital and Dolby Digital Plus sources
*2
DTS and DTS-HD High Resolution sources
*3
DSD (Super Audio CD) sources
Front left speaker Front right speaker
Listening angle: 30°