Filter
Top Products
59
En
Controlling Other Components
iPod/iPhone Playback via Onkyo Dock
UP-A1 Dock
With the UP-A1 Dock, you can easily play the music,
photos, or movies stored on your Apple iPod/iPhone
through the AV receiver and enjoy great sound.
You can use the AV receiver’s remote controller to
operate your iPod/iPhone.
■ System Function
Auto Power On
If you start iPod/iPhone playback while the AV receiver
is on standby, the AV receiver will automatically turn
on and select your iPod/iPhone as the input source.
Direct Change
If you start iPod/iPhone playback while listening to
another input source, the AV receiver will automatically
select your iPod/iPhone as the input source.
Using the AV receiver’s Remote Controller
You can use the AV receiver’s remote controller to
control basic iPod/iPhone functions (➔ page 60).
■ Using Your iPod/iPhone Alarm Clock
You can use the Alarm Clock function of your
iPod/iPhone to automatically turn on your iPod/iPhone
and the AV receiver at a specified time. The AV receiver’s
input source will automatically be set to the PORT
selector.
Note
• To use this function, your iPod/iPhone must be in the UP-A1
Dock, and the UP-A1 Dock must be connected to the AV
receiver.
• This function works only in Standard mode (➔ page 61).
• When you use this function, be sure to set the AV receiver’s
volume control to a suitable level.
• When Zone 2 is turned on, you can’t use this function.
• This function doesn’t work when alarms sounds are set on your
iPod/iPhone.
•The “Charge Mode” setting must be set to “On” to enable the
Alarm Clock function (➔ page 50).
■ Charging Your iPod/iPhone Battery
When the UP-A1 Dock with docked iPod/iPhone is
connected to the AV receiver, the battery of your
iPod/iPhone is charged. Charging occurs when AV
receiver is set to on or standby.
You can specify how the power is fed to your iPod/iPhone
when the AV receiver is in standby mode (➔ page 50).
Note
• When the UP-A1 Dock with docked iPod/iPhone is connected,
the power consumption on standby mode slightly increases.
Using the Onkyo Dock
The Dock is sold separately. Models sold are different
depending on the region.
For the latest information on the Onkyo Dock
components, see the Onkyo web site at:
http://www.onkyo.com
Before using the Onkyo Dock components, update
your iPod/iPhone with the latest software, available
from the Apple web site.
For supported iPod/iPhone models, see the
instruction manual of the Onkyo Dock.
The AV receiver may take several seconds to startup, so
you might not hear the first few seconds of the first
song.
■ Operating Notes
• Functionality depends on your iPod/iPhone model and
generation.
• Before selecting a different input source, stop your
iPod/iPhone playback to prevent the AV receiver from
selecting the iPod/iPhone input source by mistake.
• If any accessories are connected to your iPod/iPhone, the AV
receiver may not be able to select the input source properly.
• When connecting the UP-A1 Dock to the radio tuner UP-HT1
(North American models) with AUTO selected by the
tuner’s Mode Selector switch, you can switch the input source
between UP-A1 Dock and the tuner, by pressing PORT
repeatedly on the front panel.
• While your iPod/iPhone is in the UP-A1 Dock, its volume
control has no effect. If you adjust your iPod/iPhone models
volume control while it’s in the UP-A1 Dock, make sure it’s
not set too high before you reconnect your headphones.
• The Auto Power On function will not work if you set your
iPod/iPhone in the UP-A1 Dock while it is playing.
• When Zone 2 is turned on, you can’t use Auto Power On and
Direct Change functions.
• Do not turn off the power with the iPod/iPhone still connected
to this unit via the UP-A1 Dock.
• Set your iPod/iPhone in the UP-A1 Dock after the AV
receiver turns on.
•The “Charge Mode” setting must be set to “On” to enable the
Auto Power On and Direct Change functions (➔ page 50).