Filter
Top Products
44
En
■ Double Bass
`On
`Off
Turn this setting on to boost bass output by feeding bass
sounds from the front left, right, and center channels to the
subwoofer.
Note
• This function can be set only if the “Subwoofer” setting is set to
“Yes”, and the “Front” setting is set to “Full Band”.
■ Wireless Front High, Wireless Surround Back,
Wireless Subwoofer
`Yes:
The audio is output from the speakers connected to
the wireless unit.
`No
:
The audio is not output from the speakers connected
to the wireless unit.
When the wireless unit is connected to the UNIVERSAL
PORT jack on the AV receiver, you can select if you wish
to output the audio from the speakers connected to the
wireless unit.
Note
•If the “Front High” setting is set to “None” (➔ page 43),
“Wireless Front High” cannot be selected.
•If the “Surround Back” setting is set to “None” (➔ page 43),
“Wireless Surround Back” cannot be selected.
•If the “Subwoofer” setting is set to “No” (➔ page 43),
“Wireless Subwoofer” cannot be selected.
Speaker Distance
Here you can specify the distance from each speaker to the
listening position so that the sound from each speaker
arrives at the listener’s ears as the sound designer
intended.
■ Unit
`feet:
Distances can be set in feet. Range: 1.0ft to 30.0ft in
1 foot steps.
`meters:
Distances can be set in meters. Range: 0.30m to
9.00m in 0.3 meter steps.
(The default setting varies from country to country.)
■ Left, Front High Left, Center, Front High Right,
Right, Surround Right, Surround Back Right,
Surround Back Left, Surround Left, Subwoofer
`Specify the distance from each speaker to your
listening position.
Note
• These settings are not available in either of the following cases:
– a pair of headphones is connected.
–the “Audio TV Out” setting is set to “On” (➔ page 53).
–“HDMI Control (RIHD)” is set to “On” (➔ page 52) and
you’re listening through your TV speakers.
• Speakers that you set to “No” or “None” in the
“Speaker Configuration” cannot be selected (➔ page 43).
Level Calibration
Here you can adjust the level of each speaker with the
built-in test tone so that the volume of each speaker is the
same at the listening position.
■ Left, Front High Left, Center
*1
, Front High Right,
Right, Surround Right, Surround Back Right,
Surround Back Left, Surround Left
`–12dB to 0dB
to +12dB in 1 dB step.
■ Subwoofer
*1
` –15dB to 0dB to +12dB in 1 dB step.
Note
• These settings cannot be calibrated in either of the following
cases:
– a pair of headphones is connected.
–the “Audio TV Out” setting is set to “On” (➔ page 53).
–“HDMI Control (RIHD)” is set to “On” (➔ page 52) and
you’re listening through your TV speakers.
– the AV receiver is muted.
• Speakers that you set to “No” or “None” in the
“Speaker Configuration” cannot be selected (➔ page 43).
*1
For the center speaker and subwoofer, the level settings made
by using the Home menu are saved in this menu
(➔ page 37).
Tip
• If you’re using a handheld sound level meter, adjust the level of
each speaker so that it reads 75 dB SPL at the listening position,
measured with C-weighting and slow reading.
This setting is NOT set automatically by
Audyssey 2EQ
®
Room Correction and Speaker Setup
(➔ page 29).
When an optional unit is connected to the
UNIVERSAL PORT jack on the AV receiver, the
speaker setting menu may appear on screen.
This setting is set automatically by Audyssey 2EQ
Room Correction and Speaker Setup (➔ page 29).
This setting is set automatically by Audyssey 2EQ
Room Correction and Speaker Setup (➔ page 29).