Filter
Top Products
19NILES AUDIO CORPORATION – 1-800-BUY-HIFI – 305-238-4373
to that input until a signal is no longer detected. The paging input
will play in all zones at the preset volume. If there are zones that the
end-user does not desire to receive a page, follow these steps.
While in the configuration mode (see above). Press the Band Key
until [ 1234 PAGE MASTER ] shows in the display. A cursor will be
blinking under the number “1.”
Press the + key to toggle between the zones to highlight a paging zone.
The cursor under the zone number blinks when a zone is highlighted.
Press the Set key to deselect a highlighted zone as a paging zone.
A [ P ] will disappear below that zone number.
Once you reach “4” it will toggle back to “1” on the Slave. Once you
have reached “4” on the Slave it will toggle back to “1” on the Master.
Repeat these steps until all of the desired zones have been set for
your desired paging operation.
To continue to the next system configuration Party or Whole House
Mode, press the Band key once. To save your settings and to exit the
configuration mode, simultaneously hold down the Band and Set keys.
[ RELEASE BUTTONS TO CONTINUE ] appears on the display. You will return
to the source that was playing before entering the configuration mode.
PARTY OR WHOLE HOUSE MODE
This feature lets the end-user press-and-hold any Master Key for
three seconds to turn On the entire house to the same source for a
party. It also allows for the press-and-hold of the Off key to turn Off
the entire system from one zone keypad without the need to walk
around to every keypad to do so. By default all zones will respond
to Party mode. If there are zones that the end-user does not want
to turn on when a press-and-hold is initiated, follow these steps.
NOTE: THIS FEATURE ONLY DEACTIVATES THE PRESS-AND-HOLD ON AND NOT THE
OFF. THE OFF IS ALWAYS AVAILABLE AT ANY ZONE REGARDLESS OF ITS SETTING.
While in the configuration mode, (see above) press the Band Key
until [ 1234 PARTY MASTER ] shows in the display. A cursor will be
blinking under the number “1.”
Press the + to toggle between the zones. The cursor under the
zone number blinks when a zone is highlighted.
Press the Set key to deselect a highlighted zone as a Party zone. A [ W ]
will disappear below that zone number.
Once you reach “4” it will toggle back to “1” on the Slave. Once you
have reached “4” on the Slave it will toggle back to “1” on the Master.
Repeat these steps until all of the desired zones have been set for
your desired Party operation.
To continue to the next system configuration Page Mode On Volume,
press the Band key once. To save your settings and to exit the
configuration mode, simultaneously hold down the Band and Set keys.
[ RELEASE BUTTONS TO CONTINUE ] appears on the display. You will return
to the source that was playing before entering the configuration mode.
PAGE MODE VOLUME
The paging volume level for all selected zones is adjustable.
While in the configuration mode, (see above) press the Band Key
until [ PAGE MODE VOLUME = 60 ] shows in the display.
Press the + key to increase the preset volume. Press the – key to
decrease the preset volume. The factory default setting is 60.
The volume range is from 0 to 99. Hold the Set key 2 seconds to
save the new page volume.
To continue to the next system configuration Default Turn On
Volume, press the Band key once. To save your settings and to exit
the configuration mode, simultaneously hold down the Band and
Set keys. [ RELEASE BUTTONS TO CONTINUE ] appears on the display.
You will return to the source that was playing before entering the
configuration mode.
1 2 3 4
P P P P
P A G E
M A S T E R
1 2 3 4
P P
P A G E
M A S T E R
R E L E A S E B U T T O N S
T O
C O N T I N U E
1 2 3 4
W W W W
P A R T Y
M A S T E R
1 2 3 4
W W
P A R T Y
M A S T E R
R E L E A S E B U T T O N S
T O
C O N T I N U E
P A G E M O D E
V O
L U M E = 6 0
P A G E M O D E
V O
L U M E = 3 4
(CONTINUED ON NEXT PAGE)
R E L E A S E B U T T O N S
T O
C O N T I N U E