Filter
Top Products
7
Door Station Connection to Master Station
The Door Station connects to the two screw terminals
between the quick connector sockets. If the Door Station
has a bell button, it connects to the optional chime module.
1. Connect the BLACK wire from the Door Station to the screw
terminal labeled DOOR BLACK on the dmc1 Master Station.
2. Connect the RED wire from the Door Station to the screw
terminal labeled DOOR RED on the dmc1 Master Station.
3. Connect the ORANGE wire from the Door Station to the screw
terminal labeled COMMON on the chime module (if chime is used)
4. Connect the YELLOW wire from the Door Station to
one of the NOTE screw terminals on the chime module
(if chime is used). DO NOT CONNECT THE YELLOW
WIRE TO MORE THAN ONE NOTE TERMINAL.
5. Connect the shield wire from the Door Station to the terminal
labeled SHIELDS on the dmc1 Master Station. NOTE: THE
SHIELD WIRE MUST BE INSULATED TO PREVENT IT
FROM TOUCHING ADJACENT COMPONENTS. SLIDE
ON SOME INSULATION FROM A STRIPPED WIRE.
Antenna Connections
The dmc1 contains an AM/FM tuner. Radio reception
requires installation of an AM wire lead antenna, and an FM
dipole antenna. The antennas should have been installed
during the rough-in and require connecting to the dmc1
Master Station.
1. The AM antenna is the single ORANGE wire lead that has the
ferrite fi lter on it. Connect the ORANGE wire to the AM ANTENNA
terminal on the side of the tuner module in the dmc1 Master
Station. The GROUND terminal remains un-connected.
2. The FM antenna is the coax wire with the Type “F” connector.
Connect the coax wire to the FM ANTENNA connector on
the side of the tuner module in the dmc1 Master Station.
Door Release Connection
The dmc1 Master Station can be wired to a Model DRW
electric door strike. The door release relay has normally open
contacts that are rated at 2 Amps @ 24 Volts AC/DC. The
relay can be activated from the dmc1 Master Station or remote
scan Room Stations (Model dmc1RS) by pressing the volume
up and volume down buttons together for four seconds. The
relay will deactivate when the buttons are released.
1. Identify the two cables labeled “Door Release”.
2. Use a wire nut to connect one wire from the transformer
cable to one wire from the door strike.
3. Connect the remaining wires from each cable to the terminals
marked DOOR RELEASE on the dmc1 Master Station.
External Music Source Connection
Audio from the optional AWP wall plate connects to the
dmc1 auxiliary audio inputs.
Follow these steps if using the audio input wall plate
1. Identify the two RCA cables labeled “AUX INPUT”.
2. Insert the left audio cable RCA plug into the
AUX L jack on the dmc1 Master Station.
3. Insert the right audio cable RCA plug into the
AUX R jack on the dmc1 Master Station.
MS4DCXSC
CABLE TO
DOOR STATION
BLACK
WIRE
RED
WIRE
DOOR BLACK DOOR RED
SHIELD
WIRE
NOTE: SLIDE
INSULATION
ON SHIELD
WIRE TO
PREVENT
SHORTS
SHIELD
ORANGE
WIRE
YELLOW
WIRE
COMMON
TERMINAL
NOTE
TERMINAL
(CONNECT TO
ONLY ONE)
Figure 17. Door Station Master Station and Chime
Connections
AM ANTENNA
WIRE
FM ANTENNA
COAX CABLE
AM ANTENNA
FERRITE FILTER
(HANGS INSIDE
WALL HOUSING)
AM ANTENNA
CONNECTS TO
THIS TERMINAL ONLY
FM ANTENNA
AM ANTENNA
Figure 18. AM and FM Antenna Connections
FROM RT11
TRANSFORMER
TO ELECTRIC
DOOR STRIKE
DOOR RELEASE
TERMINALS
PBVM127X1 CABLE
Figure 19. Door Release Wiring
LEFT
AUXILIARY
INPUT
RIGHT
AUXILIARY
INPUT
PLUG EXTERNAL AUDIO
CABLES INTO LEFT & RIGHT
AUDIO INPUT JACKS
Figure 20. Auxiliary Input Jacks on Master Station