Filter
Top Products
10
ENGLISH
TUNER MODE
AMP MODE
2 31
5 64
8
0
97
MEMO
CLEAR
DSS
AMP
AUX2
AUX1
TAPE
TUNER
CD
CD-R
MD
VCRDVD
TV
SOURCE
OFF
ON/OFF
POWER
ON
D4
D5
D2
M
D1
D3
D5
OK
VOL
CH
PREV
MUTE
MENU
EXIT
GUIDE
TEST
CH.SEL
SURR
7.1CH
ATT
SPK-AB
DISP
OSD
SLEEP
12
LIGHT
Learning Remote Controller
RC1400
D1
D5
D4
D2
D3
D5
2 31
5 64
8 97
TEST
CH.SEL
SURR
7.1CH
ATT
SPK-AB
DISP
OSD
SLEEP
TUNER
0
CH
GUIDE
MEMO
CLEAR
USE
PAGE
1
2 31
5 64
8
0
97
MEMO
CLEAR
DSS
AMP
AUX2
AUX1
TAPE
TUNER
CD
CD-R
MD
VCRDVD
TV
SOURCE
OFF
ON/OFF
POWER
ON
D4
D5
D2
M
D1
D3
D5
OK
VOL
CH
PREV
MUTE
MENU
EXIT
GUIDE
TEST
CH.SEL
SURR
7.1CH
ATT
SPK-AB
DISP
OSD
SLEEP
12
LIGHT
Learning Remote Controller
RC1400
D1
D5
D4
D2
D3
D5
SOURCE
OFF
ON/OFF
POWER
ON
OK
2 31
5 64
8 97
TEST
CH.SEL
SURR
7.1CH
ATT
SPK-AB
DISP
OSD
SLEEP
MENU
TAPE
DSS
AUX2
AUX1
TUNER
CD
CD-R
MD
VCRDVD
TV
AMP
VOL
EXIT
MUTE
USE
PAGE
123
4
SOURCE ON/OFF Turns the SR7400 on and off
POWER ON Turns the SR7400 on
POWER OFF Turns the SR7400 off
D1 - D5 / >(Page) (Refer to page vi)
VOL +/- Adjust the over all sound level
MUTE Decreases the sound temporarily
Cursor Move the cursor for setting in"On screen display" mode
OK Enter the "On screen display"
Confirms the setting in "On screen display" mode
MENU Displays the current setting on the monitor
EXIT Exits from SETUP MENU
TEST (1) Enter the test tone menu
CH.SEL (2) Call up SETUP MENU and adjusts speaker levels or 7.1ch input
level
SURR (3) Selects the surround mode
7.1CH (4) Selects the 7.1CH IN
ATT (5) Reduces the input level
SPK-AB (6) Selects the speaker system
DISP (7) Changes the front display mode
OSD (8) Selects the "On screen display" on and off
SLEEP (9) Sets the sleep timer function
Function selector Selects a particular source component
D1 - D5 / >(Page) (Refer to page vi)
CH +/- Selects a preset station up and down
GUIDE Selects the "Frequency direct input"
0-9 Input the numeric
MEMO Enter the tuner preset memory numbers
CLEAR Clears the inputting
TUNER Selects a frequency band
2 31
5 64
8
0
97
MEMO
CLEAR
DSS
AMP
AUX2
AUX1
TAPE
TUNER
CD
CD-R
MD
VCRDVD
TV
SOURCE
OFF
ON/OFF
POWER
ON
D4
D5
D2
M
D1
D3
D5
OK
VOL
CH
PREV
MUTE
MENU
EXIT
GUIDE
TEST
CH.SEL
SURR
7.1CH
ATT
SPK-AB
DISP
OSD
SLEEP
12
LIGHT
Learning Remote Controller
RC1400
2.
6.
4.
5.
3.
3.
21
8
0
OK
USE
PAG E
1
USE
PAG E
12
LEARN
LEARN
LEARN
56
34
12
USE
PAG E
12
SETTING THE TIME
Example: Setting to 6:20PM (18:20)
When you bought this remote control and insert
the batteries to the remote control at first, the steps
1 to 3 are skipped.
Starts from step 4 to set the time.
1.
Hold down the M button for three seconds or
more.
The menu is displayed.
2.
Press the > button once.
This displays second page (SETUP).
3.
Press the D4 (CLOCK) direct button.
The “ ” indicator blinks and the clock indicator
displays “0:00”.
4.
Press the 1 and 8 numeric button to set the
hour indicator.
The hour indicator displays “18”.
The minute indicator blinks “_”.
5.
Press the 2 and 0 numeric button to set the
minute indicator.
The minute indicator displays “20”.
The hour indicator blinks.
6.
Press the OK cursor button to start the clock.
The clock starts from 0 second at the time that was
set and return to normal (USE) mode.
Whenever the batteries are replaced, the clock
shows 00:00. Please reset the clock. (The time
setting is not backed up.)
CHECKING THE TIME
To check the time, hold down the > button for three
seconds or more. The current time is displayed for
five seconds.
Note
Although the remote control uses a quartz clock,
the time may become out of sync over the course
of operation. Be sure to correct the clock from time
to time.
GENERAL INFORMATION OF RC1400
TO SR7400
To control the SR7400 by your RC1400, you have
to select the device AMP or TUNER by pressing
the function selector button. Please refer below
for the details in AMP and TUNER mode.
03.10.13, 9:24 AMPage 10