Filter
Top Products
35
ENGLISH
BASIC OPERATION (TUNER)
LISTENING TO THE TUNER
Frequency scan step for AM is selectable.
Default setup is 10 kHz step, if your country’s standard is 9 kHz step,
Press TUNER button on the remote more than 6 seconds. Scan step
will change.
Note:
• Preset memory for the tuner will clear by changing this setup.
AUTO TUNING
(USING THE SR7300)
1.
To select tuner and desired band (FM or AM), press the TUNER
button on the front panel.
2.
F/P button on the front panel to display the frequency.
3.
Press the TUNING or button on the front panel for more than
1 second to start the Auto tuning function.
4.
Automatic searching begins then stops when a station is tuned in.
(Using the remote control unit)
1.
To select tuner and desired band (FM or AM), press TUNER
button twice within in two seconds on the remote.
2.
Press
55
55
5 or
66
66
6
more than 1 second on the remote.
3.
Automatic searching begins then stops when a station is tuned in.
If tuning does not stop at the desired station, use to the “Manual
tuning” operation.
MANUAL TUNING
(USING THE SR7300)
1.
To select tuner and desired band (FM or AM), press the TUNER
button on the front panel
2.
Press the F/P (Frequency/Preset) button on front panel, to
appears frequency on the display.
3.
Press the TUNING or button.
(Using the remote control unit)
1.
To select tuner and desired band (FM or AM), press TUNER
button twice within in two seconds on the remote.
2.
Press
55
55
5 or
66
66
6 on the remote to tune in the desired station.
DIRECT FREQUENCY CALL
1.
To select tuner and desired band (FM or AM), press TUNER
button twice within in two seconds on the remote.
2.
Press the F.DIR on the remote, display will show “FREQ - - - -”.
3.
Input your desired station’s frequency with ten keypad on the
remote.
4.
The desired station will automatically be tuned.
(FM) TUNING MODE (AUTO STEREO OR MONO)
When in the auto stereo mode, AUTO indicator keeps to light on the
display.
The “ST” indicator lights on when a stereo broadcast is tuned in.
At open frequencies, the noise is muted and the “TUNED” and “ST”
indicators turn off.
If the signal is weak, it may be difficult to tune into the station in stereo.
In such a case, press the MODE button on the front panel or press
T.MODE button on the remote.
“AUTO” indicators turn off ,FM stereo broadcasts are received in
monaural and the “ST” indicator turns off.
To return to auto stereo mode, press the MODE button or press T.MODE
button on the remote again. AUTO indicator lights on the display.
PRESET MEMORY
With this unit you can preset up to 50 FM/AM stations in any order.
For each station, you can memorize the frequency and reception
mode if desired.
AUTO PRESET MEMORY
This function automatically scans the FM and AM band and enters all
stations with proper signal strength into the memory.
1.
To select FM , press the TUNER button on the front panel.
2.
While pressing the MEMORY button, press the TUNING button
to up.
“AUTO PRESET” will appear on the display, and scanning starts
from lowest frequency.
UP
VOLUME
DOWN
MEMORY
TUNING
MODE
F/P
R
S-DIRECT MULTIROOM
MUTE
A/D7.1CH INPUT
A
/B
AUX1 INPUT
S-VIDEODIGITAL VIDEO L AUDIOR
DSS/VCR2
AUX1 AUX2
VCR1
DVD
CD
CD-R
TAPE
TUNER
ATT
3. 2. 1.
2.
1.
UP
VOLUME
DOWN
MEMORY
TUNING
MODE
F/P
R
S-DIRECT MULTIROOM
MUTE
A/D7.1CH INPUT
A
/B
AUX1 INPUT
S-VIDEODIGITAL VIDEO L AUDIOR
DSS/VCR2
AUX1 AUX2
VCR1
DVD
CD
CD-R
TAPE
TUNER
ATT
3. 2. 1.
2.
1.
1.
3.
2.
0
UP
VOLUME
DOWN
MEMORY
TUNING
MODE
F/P
CLEAR
S-DIRECT MULTIROOM
MUTE
A/D7.1CH INPUTSPEAKRS A/B
AUX1 INPUT
S-VIDEODIGITAL VIDEO L AUDIOR
DSS/VCR2
AUX1 AUX2
VCR1
DVD
TV
CD
CD-R
TAPE
TUNER
ATT
AV SURROUND RECEIVER SR7300
UP
SURROUND
VOLUME
DOWN
MEMORY
TUNING
MODE
F/P
CLEAR
S-DIRECT MULTIROOM
MUTE
A/D7.1CH INPUTSPEAKRS A/B
POWER ON/STANDBY
PHONES
ENTER
STANDBY
AUX1 INPUT
S-VIDEODIGITAL VIDEO L AUDIOR
DSS/VCR2
AUX1 AUX2
VCR1
DVD
TV
CD
CD-R
TAPE
TUNER
ATT
SELECT
2.4.2.5. 3.
2)
1. 3.
1)