Filter
Top Products
24
ENGLISH
Notes:
• Speakers that you selected “None” for in the Speaker Size menu
will not appear.
• The setting of Surr.Back L and Surr.Back R appears if set for
two surround back speakers in the Speaker Size menu.
• The setting of Surr.Back appears if set for one surround back
speaker in the Speaker Size menu.
• To adjust the speaker levels for 7.1-channel input sources, you
will need to use the 7.1CH-INPUT sub menu. (See page 26).
3 PREFERENCE
1.
Select “PREFERENCE” in SETUP MAIN MENU with or
cursor button, and press the OK button.
2.
To select a desired content, press or cursor button.
STANDBY MODE: When this function is set to “ECONOMY”, you
can reduce the power consumption to standby
condition.
Note:
TV-AUTO , MULTI RC control and
RC232C are disable in “ECONOMY” setting.
TV AUTO: Select the TV AUTO ON/OFF function to enable
or disable with or cursor button.
(refer to page 32)
OSD Info: Select the OSD information function to enable or
disable with or cursor button.
If you select “ENABLE”, SR7300 will display the
status of the feature (Volume up/down, input
select, etc..) on the TV monitor. But if you do not
desire this information, select “DISABLE ”.
If you finish the setup in this item, move cursor to “MAIN” with or
cursor buttons and press OK button.
4 SURROUND
1.
Select “SURROUND” in SETUP MAIN MENU with or cursor
button, and press the OK button.
2.
To select a desired content , press or cursor button.
SURR-MODE : Select the desired surround mode with or
cursor button.
HT-EQ : Select to active the HT-EQ with or cursor
button.
The tonal balance of a film soundtrack will be
excessively bright and harsh when played back
over audio equipment in the home. This is
because film soundtracks were designed to be
played back in large movie theater environments.
Activating the HT-EQ feature when watching a
film made for movie theaters corrects this and
restores the correct tonal balance.
The HT-EQ feature can be activated only while
in Dolby Pro Logic Mode, or while decoding
Dolby Digital or DTS encoded material.
LFE LEVEL : Select the output level of the LFE signal included
in the Dolby Digital signal or the DTS signal.
Select 0 dB, -10 dB or OFF with Left or Right
cursor button.
CHANNEL LEVEL
CENTER LEVEL: Set the effect level of the center speaker between –
10 and +10 dB level in 1 dB level interval .
• If “None” was selected for the Center speaker setting in the
Speaker size, then this setting will not appear.
SURR L LEVEL: Set the level of the Surround left speaker between –
10 and +10 dB level in 1 dB level interval.
• If “None” was selected for the Surround left speaker setting in
the Speaker size, then this setting will not appear.
SURR R LEVEL: Set the level of the Surround speaker between –10
and +10 dB level in 1 level interval.
• If “None” was selected for the Surround right speaker setting in
the Speaker size, then this setting will not appear.
SURR BACK LEVEL: Set the effect level of the Surround Back
speaker between –10 and +10 dB level in 1 dB
level interval.
• If “None” was selected for the Surround back speakers setting
in the Speaker size, then this setting will not appear.
SUB W LEVEL: Set the effect level of the subwoofer speaker
between –15 and +10 dB level in 1 dB level interval.
• If “None” was selected for the Subwoofer speaker setting in the
Speaker size, then this setting will not appear.
If you finish the setup in this item, move cursor to “MAIN” with or
cursor buttons and press OK button.
3 PREFERENCE
STANDBY MODE : ECONOMY
TV-AUTO : DISABLE
OSD I NFO : ENABLE
MA I N EX I T
4 SURROUND
SURR .MODE : AUTO
HT-EQ : OFF
LFE LEVEL : 0 dB
CENTER : 0 dB
SURR L : 0 dB
SURR R : 0 dB
SURR BACK : 0 dB
SUB W : 0 dB
MA I N EX I T