Filter
Top Products
19
ENGLISH
ENGLISH
TEMPORARILY TURNING OFF THE
SOUND
To temporarily silence all speaker outputs such as
when interrupted by a phone call, press the MUTE
button on the front panel or MUTE button on the
remote.
This will interrupt the output to all speakers and the
head-phone jack, but it will not affect any recording
or dubbing that may be in progress.
When the system is muted, the display will show
“MUTE” .
Press the MUTE button again to return to normal
operation.
BASIC OPERATION
(PLAY BACK)
SELECTING AN INPUT SOURCE.
Before you can listen to any input media, you must
first select the input source on the SR6400.
Example : DVD
To select DVD, simply press the DVD button on the
front panel or press the DVD button on the remote.
After you have selected DVD, simply turn on the
DVD player and play the DVD.
•
As the input source is changed, the new input
name will appear momentarily an OSD information
on the video display. The input name will also
appear in the display, on the front-panel.
•
As the input is changed, the SR6400 will
automatically switch to the digital input, surround
mode, attenuation, and night mode status which
were entered during the configuration process
for that source.
•
When an audio source is selected, the last video
input used remains routed to the VCR1 & DSS/
VCR2 Outputs and Monitor Outputs. This permits
simultaneous viewing and listening to different
sources.
•
When a Video source is selected, the video signal
for that input will be routed to the Monitor Outputs
jacks and will be viewable on a TV monitor
connected to the SR6400.
If a component video input is connected to the
DVD or DSS component inputs, it will be routed
to the Component Video Output. Make certain
that your TV is set to the proper input to view the
signal.
SELECTING THE SURROUND MODE
Example : AUTO SURROUND
To select the surround mode during playback, turn
the SELECT knob on the front panel or press the
surround mode button on the remote .
ADJUSTING THE MAIN VOLUME
Adjust the volume to a comfortable level using the
VOLUME control knob on the front panel or VOL
/ buttons on the remote.
To increase the volume, turn the VOLUME knob
clockwise or press VOL button on the remote, to
decrease the volume, turn counterclockwise or
press VOL button on the remote.
Notes:
•
The volume can be adjusted within the range of – ∞
to 18 dB, in steps of 1 dB.
•
However, when the channel level is set as described
on page 17, if the volume for any channel is set at
+1 dB or greater, the volume cannot be adjusted up
to 18 dB.
(In this case the maximum volume adjustment
range is “18 dB - Maximum value of channel level)
ER SR6400
MEMORY
TUNING
MODE
CLEAR
DSS/VCR2
AUX
VCR1
DVD
TV
CD
CD-R
TAPE
TUNER
S-DIRECT DISPLAY
A/D6.1CH INPUTSPEAKERS A/B
F/P
ADJUSTING THE TONE (BASS &
TREBLE) CONTROL.
During a listening session you may wish to adjust
the Bass and Treble Control to suit your listening
tastes or room acoustics.
(Using the SR6400)
To change the selector mode , press the SELECT
button, until "BASS" or "TREBLE" is shown on the
front display.
Turn the SELECTOR knob to the desired level of tone
control.
(Using the remote control unit)
To adjust the bass effect , press BASS or BASS
on the remote.
To adjust the treble effect , press TREBLE or
TREBLE on the remote.
Notes :
• The tone control function can work in the AUTO
Surround, Stereo, Dolby PL2, DTS, DTS-ES, and
Multi Ch. Stereo mode.
AV SURROUND RECEIVER SR6400
SELECTOR
MEMORY
CLEAR
POWER ON/STANDBY
PHONES
ENTER
STANDBY
SELECT
DSS/V
VCR1
DVD
TV
6.1CH INPUTSPEAKERS A/B
UP
VOLUME
DOWN
MODE
MUTE
AUX INPUT
S-VIDEO VIDEO L AUDIOR
ATT
CD
CD-R
TAPE
TUNER
S-DIRECT DISPLAY
F/P
AV SURROUND RECEIVER SR6400
SELECTOR
MEMORY
CLEAR
POWER ON/STANDBY
PHONES
ENTER
STANDBY
SELECT
DSS/VC
VCR1
DVD
TV
6.1CH INPUTSPEAKERS A/B
UP
VOLUME
DOWN
MODE
MUTE
AUX INPUT
S-VIDEO VIDEO L AUDIOR
ATT
CD
TAPE
TUNER
S-DIRECT DISPLAY
F/P