Marantz SR5400U Stereo Receiver User Manual


 
19
ENGLISH
ENGLISH
SRS DIALOG:
Set the SRS DIALOG level between 0 and 6 in 1
level intervals with the or cursor buttons.
This can be popped out of the surround audio
effects, allowing the listener to easily discern
what the actors say.
If NONE was selected for the Center speaker
setting, in the Speaker size set up menu, then this
setting will not appear.
After you complete this portion of the set up, move
the cursor to MAIN with the or cursor buttons
and press the OK button.
7 6.1 CH INPUT LEVEL
This sub-menu is to adjust the speaker levels for
6.1-channel input sources.
Here you will adjust the volume for each channel
so that they are all heard by the listener at the
same level.
1.
Select 6.1CH IN in the MAIN SETUP MENU
with the or cursor buttons, and press the
OK button.
2.
To Select desired channel, press the or
cursor buttons.
3.
Using the or cursor buttons, adjust the
volume level of each channel.
4.
After you complete this portion of the set up,
move the cursor to MAIN with the or
cursor buttons and press the OK button.
Note:
These settings will be memorized to 6.1CH INPUT
source.
4 SURROUND
1.
Select SURROUND in the SETUP MAIN
MENU with the or cursor buttons, and press
the OK button.
2.
To select a desired content , press the or
cursor buttons.
SURR.MODE :
Select the desired surround mode with the or
cursor buttons.
HT-EQ :
Select to active the HT-EQ with the or cursor
buttons.
The tonal balance of a film soundtrack will be
excessively bright and harsh when played back
over audio equipment in the home. This is
because film soundtracks were designed to be
played back in large movie theater environments.
Activating the HT-EQ feature when watching a
film made for movie theaters corrects this and
restores the correct tonal balance.
The HT-EQ feature can be activated only while
in Dolby Pro Logic Mode, or while decoding
Dolby Digital or DTS encoded material.
LFE LEVEL :
Select the output level of the LFE signal included
in the Dolby Digital signal or the DTS signal.
Select 0 dB, -10 dB or OFF with the or cursor
buttons.
CHANNEL LEVEL
CENTER LEVEL:
Set the effect level of the center speaker between
10 and +10 dB level in 1 dB level intervals.
If None was selected for the Center speaker
setting, in the Speaker size set up menu, then this
setting will not appear.
SURR L LEVEL:
Set the level of the Surround left speaker between
10 and +10 dB level in 1 dB level intervals.
If None was selected for the Surround left
speaker setting, in the Speaker size set up menu,
then this setting will not appear.
4 SURROUND
SURR .MODE : AUTO
HT-EQ : OFF
LFE LEVEL : 0 dB
CENTER : 0 dB
SURR L : 0 dB
SURR R : 0 dB
SURR BACK : 0 dB
SUB W : 0 dB
MA I N EX I T
SURR R LEVEL:
Set the level of the Surround right speaker between
10 and +10 dB level in 1dB level intervals.
If None was selected for the Surround right
speaker setting, in the Speaker size set up menu,
then this setting will not appear.
SURR BACK LEVEL:
Set the effect level of the Surround Back speaker
between 10 and +10 dB level in 1 dB level
intervals.
If None was selected for the Surround back
speakers setting, in the Speaker size set up menu,
then this setting will not appear.
SUB W LEVEL:
Set the effect level of the subwoofer speaker
between 15 and +10 dB level in 1 dB level
intervals.
If None was selected for the Subwoofer speaker
setting, in the Speaker size set up menu, then this
setting will not appear.
After you complete this portion of the set up, move
the cursor to MAIN with the or cursor buttons
and press the OK button.
5 PL II (PRO LOGIC II) MUSIC
PARAMETER
Pro Logic II-Music mode creates a rich and
enveloping surround ambience from stereo sources
such as CDs.
In this
mode, SR5400 includes three controls to
fine-tune the soundfield as follows.
Select PRO LOGIC II in the SETUP MAIN MENU
with the or cursor buttons, and press the OK
button.
PARAMETER:
Select DEFAULT or CUSTOM with the or
cursor buttons.
If you select CUSTOM, you can adjust three
parameters as listed below.
PANORAMA:
Select the Panorama mode On or Off with the or
cursor buttons.
Panorama wraps the sound of the front left and right
speakers around you, for an exciting perspective.
DIMENSION:
Set the Dimension level between 0 and 6 level in
1 level intervals with the or cursor buttons.
Adjust the soundfield either towards the front or
towards the rear.
This can be useful to help achieve a more suitable
balance from all the speakers with certain
recordings.
CENTER WIDTH:
Set the Center width level between 0 and 7 in 1
level intervals with the or cursor buttons.
Center Width allows you to gradually spread the
center channel sound into the front left and right
speakers.
At its widest setting, all the sound from the
center is mixed into the left and right.
This control may help achieve a more spacious
sound or a better blend for the front image.
If None was selected for the Center speaker
setting, in the Speaker size set up menu, then
this setting will not appear.
After you complete this portion of the set up, move
the cursor to MAIN with the or cursor buttons
and press the OK button.
6 CS II (CIRCLE SURROUND II)
PARAMETER
1.
Select CS II in the SETUP MAIN MENU with
the or cursor buttons, and press the OK
button.
2.
To Select desired contents as below, press
the or cursor buttons.
TRUBASS:
Set the TRUBASS level between 0 and 6 level in
1 level interval with the or cursor buttons.
TRUBASS produced by the speakers are an
octave below the actual physical capabilities of the
speakers adding exciting, deeper bass effects.
5PL II MUS IC PARAMETER
PARAMETER : DEFAULT
PANORAMA : OFF
DIMENSION : 3
CENTER WI DTH : 3
MA I N EX I T
6CSII PARAMETER
TRUBASS : 0
SRS D I ALOG : 0
MA I N EX I T
7 6 .1 CH I NPUT LEVEL
FRONT L : 0 dB
CENTER : 0 dB
FRONT R : 0 dB
SURR . R : 0 dB
SURR .BACK : 0 dB
SURR . L : 0 dB
SUB W : 0 dB
MA I N EX I T