Filter
Top Products
24
ENGLISH
OTHER FUNCTION
TV AUTO ON/OFF FUNCTION
This function allows the component connected to
the TV-VIDEO in jack to control the power (ON/
OFF) to the SR5400.
AUTO POWER ON
1.
Be sure the TV auto mode is ENABLED.
(Refer page 18 : System Setup)
2.
Connect your TV TUNER (etc) to the TV-
VIDEO in terminal. Be sure to connect the
VIDEO input.
3.
Turn OFF the power to the TV TUNER and
the SR5400.
4.
Turn ON the TV TUNER and tune in a receivable
station.
5.
When the station is received, the SR5400
turns ON and TV is selected automatically.
AUTO POWER OFF
1.
In the above situation, turn the TV TUNER
OFF or select a channel that does not contain
any broadcast.
2.
The power to the SR5400 switches to STANDBY
after approx. 5 minutes.
Notes:
• AUTO POWER OFF is canceled if the SR5400 is
set to a source other than TV.
The function reactivates when TV is selected
again.
• Some TV broadcasts may cause the TV AUTO
FUNCTION to turn ON.
• The S-Video terminal does not support “TV AUTO
ON/OFF” function.
ATTENUATION TO ANALOG INPUT
SIGNAL
If the selected analog audio input signal is greater
than the capable level of internal processing, the
“PEAK” indicator will light up on the front display.
If this happens, you should press the ATT button
on the front panel or on the remote.
“ATT” indicator will be illuminated when this function
is activated. The signal-input level is reduced by
about half. Attenuation will not work with the output
signal of TAPE-OUT, CD-R/MD-OUT, VCR1-OUT
and DSS/VCR2-OUT.
This function is memorized for each individual
input source.
LISTENING THROUGH HEADPHONES
This jack may be used to listen to the SR5400’s
output through a pair of headphones. Be certain that
the headphones have a standard 1/4" stereo phono
plug. (Note that the speakers will automatically be
turned off when the headphone jack is in use.)
Notes:
• When using headphones, the surround mode will
change to STEREO and TruSurround (TS)
headphones by SURROUND MODE selector.
• The surround mode returns to the previous setting
as soon as the plug is removed from the jack.
VIDEO ON/OFF
When no video signal is connected to the SR5400
or a DVD, etc., is connected directly to your TV, the
unnecessary video circuit can be turned off by
selecting the “VIDEO OFF” setting.
To select video off, press the VIDEO OFF button
on the front panel.
DISPLAY MODE
You can select the display mode for the front display
of the SR5400.
To select this mode, press the DISPLAY on the
remote control.
When this button is pressed, the display mode is
switched in the following sequence.
→ Surround Mode → Auto-display Off → Display
Off → Input Function → Surround Mode....
In Auto display off mode, the display is off. But, if
you make a change to the unit such as input or
surround mode, the display will show that change,
then go back to off after about 3 seconds. When
changing the volume, it is not displayed.
In Display off mode, the display is off completely.
Notes:
• Only the DISP indicator will be illuminated on the
front display, in display off condition
AV SURROUND RECEIVER SR5400
SELECTOR
MEMORY
TUNINGCLEAR
POWER ON/STANDBY
PHONES
ENTER
STANDBY
SELECT
DSS/VCR2
AUX
VCR1
DVD
TV
A/D6.1CH INPUTVIDEO OFF
UP
VOLUME
DOWN
MODE
MUTE
AUX INPUT
S-VIDEO VIDEO L AUDIOR
ATT
CD
CD-R
TAPE
TUNER
S-DIRECT DISPLAY
F/P
AV SURROUND RECEIVER SR5400
DOWN
MEMORY
TUNING
MODE
CLEAR
MUTE
PHONES
ENTER
S-VIDE
DSS/VCR2
AUX
VCR1
DVD
TV
CD
CD-R
TAPE
TUNER
S-DIRECT DISPLAY
A/D6.1CH INPUTVIDEO OFF
F/P
DISP MULTI AUTO TUNED STV
–
OFFNIGHT PEAK ANALOG
DIGITAL
ATT
SLEEP
SURR
AUTO
DIRECT DISC 6.1MTX 6.1SPKRABEQ
DIGITAL
SURROUND
PCM
L
C
R
SL SSR
LFE
AV SURROUND RECEIVER SR5400
MEMORY
TUNINGCLEAR
PHONES
ENTER
DSS/VCR2
AUX
VCR1
DVD
TV
CD
CD-R
TAPE
S-DIRECT
A/D6.1CH INPUTVIDEO OFF
F/P
DISP MULTI AUTO TUNED STV
–
OFFNIGHT PEAK ANALOG
DIGITAL
ATT
SLEEP
SURR
AUTO
DIRECT DISC 6.1MTX 6.1SPKRABEQ
DIGITAL
SURROUND
PCM
L
C
R
SL SSR
LFE
SELECTING ANALOG AUDIO INPUT
OR DIGITAL AUDIO INPUT
If you have already assigned the digital inputs, you
can temporarily select the audio input mode for
each input source with the A/D button on the remote
controller or front panel.
When this button is pressed, the input mode is
switched in the following sequence.
→ Digital Auto → Digital → Analog → Digital Auto....
In Digital Auto mode, the types of signals being
input to the digital and analog input jacks for the
selected input source are detected automatically.
If no digital signal is being input, the analog input
jacks are selected automatically.
In Digital mode, input is fixed to an assigned digital
input terminal.
In analog mode, the analog input jacks are selected.
This selecting is temporary, so the result will not be
stored in memory.
If you need to change the input mode completely,
use SYSTEM SETUP in OSD menu system. (see
page 17)
ROUND RECEIVER SR5400
MEMORY
TUNING
MODE
CLEAR
PHONES
ENTER
DSS/VCR2
AUX
VCR1
DVD
TV
CD
CD-R
TAPE
TUNER
S-DIRECT DISPLAY
A/D6.1CH INPUTVIDEO OFF
F/P
DISC/DECK
PTY
ATT.
F.DIRECT
DISP./RDS
TUNE/SEARCH
MODE
TREBLE
BASS
SYSTEM REMOTE CONTROLLER
RC5400SR
+/A
/VCR
/ANT
–/B
F.DIRECT
DISP./RDS
TUNE/SEARCH
MODE
TREBLE
CHANNEL/SKIP
BASS
A/D
P.SCAN
6.1CH IN
STEREO
M-CH ST
MEMO
CLEAR
DISPLAY
NIGHT
CSII EX/ES DSP
DTS
S-DIRECT
AUTO
321
654
98
0
7
T.TONE
MENU OFF
SETUP/
F.DIRECT
DISP./RDS
TUNE/SEARCH
MODE
TREBLE
CHANNEL/SKIP
BASS
A/D
P.SCAN
6.1CH IN
STEREO
M-CH ST
MEMO
CLEAR
DISPLAY
NIGHT
CSII EX/ES DSP
DTS
S-DIRECT
AUTO
321
654
98
0
7
T.TONE
MENU OFF
SETUP/