Filter
Top Products
6
ENGLISH
b
MONITOR OUT
This is a monitor output and each one includes
both composite video and S-video configurations.
When connecting two video monitors or
televisions, be aware that the OSD interface can
be used with both MONITOR OUT connections.
n
AC IN
Connect to an AC power outlet.
SR5400 has to be powered by 120 V AC only.
m
AC OUTLETS
Connect the AC power cables of components such as
a DVD and CD player to these outlets. SWITCHED
and UNSWITCHED outlets are provided.
The one marked SWITCHED provides power only
when the SR5400 is turned on and is useful for
components which you use every time you play
your system.
The one marked UNSWITCHED is always live as
long as the SR5400 is plugged into a live outlet.
A component connected here may be left on
permanently, or may be switched off with via its own
power switch.
Caution:
•
In order to avoid potential turn-off thumps, anything
plugged into these outlets should be powered up
before the SR5400 is turned on.
•
The capacity of this AC outlet is 120W. Do not
connect devices that consume electricity more than
the capacity of these AC outlets. If the total power
consumption of the connected devices exceeds the
capacity, the protection circuit shuts down the
power supply.
,
Speaker outputs terminals
Six terminals are provided for the front left, front
right, front center, surround left, surround right and
surround back speakers.
.
Subwoofer Output
Connect this jack to the line level input of a
powered subwoofer. If an external subwoofer
amplifier is used, connect this jack to the
subwoofer amplifier input. If you are using two
subwoofers, either powered or with a 2 channel
subwoofer amplifier, connect a “Y” connector to
the subwoofer output jack and run one cable from
it to each subwoofer amplifier.
⁄0
6.1 CHANNEL INPUT
By connecting a DVD Audio player, SACD
multichannel player, or other components that has
a multichannel port, you can playback the audio
with 5.1 channel or 6.1 channel outputs.
⁄1
REMOTE CONT. IN/OUT terminals
Connect to a Marantz component equipped with
remote control (RC-5) terminals.
⁄2
AUDIO IN/OUT (CD, TAPE, CD-R, TV,
DVD, VCR1, DSS/VCR2)
These are the analog audio inputs and outputs.
There are 7 audio inputs (4 of which are linked to
video inputs) and 4 audio outputs (2 of which are
linked to video outputs). The audio jacks are
nominally labeled for cassette tape decks,
compact disc players, DVD players and etc.... The
audio inputs and outputs require RCA-type
connectors.
⁄3
DIGITAL INPUT (Dig.1 - 4) / OUTPUT
(coaxial, optical)
These are the digital audio inputs and outputs.
There are 2 digital inputs with coaxial jacks, 2 with
optical jacks.
The inputs accept digital audio signals from a
compact disc, LD, DVD, or other digital source
component.
For digital output, there is 1 coaxial output and 1
optical output.
The digital outputs can be connected to MD
recorders, CD recorders, DAT decks, or other
similar components.
REAR PANEL
c
COMPONENT VIDEO INPUT/OUTPUT
If your DVD player or other device has component
video connectors, be sure to connect them to
these component video connectors on the
SR5400. The SR5400 has two component video
input connectors to obtain the color information (Y,
C
B
, C
R
) directly from the recorded DVD signal or
other video component and one component video
output connector to output it directly into the matrix
decoder of the display device.
By sending the pure DVD component video signal
directly, the DVD signal forgoes the extra
processing that normally would degrade the image.
The result is vastly increased image quality, with
incredibly life like colors and crisp detail.
Notes:
• This component video output will not display the
OSD menu system.
v
Preamp Outputs (L, R, SL, SR, SB, C)
Jacks for L(front left), R (front right), C (Center), SL
(surround left), SR (surround right) and SB (surround
back).
Use these jacks for connection to external power
amplifiers.
z
VIDEO IN/OUT (TV, DVD, VCR1, DSS/
VCR2)
These are the video inputs and outputs. There are
4 video inputs and 2 video outputs and each one
includes both composite video and S-video
configurations. Connect VCRs, DVD players, and
other video components to the video inputs.
S-video sources can be viewed through the S-
video outputs, and composite sources can only be
viewed through the composite output.
The 2 video output channels can be used to be
connected to video tape recorders for making
recordings.
x
FM antenna terminal (75 ohms)
Connect an external FM antenna with a coaxial
cable, or a cable network FM source.
AM antenna and ground terminals
Connect the supplied AM loop antenna. Use the
terminals marked “AM” and “GND”. The supplied
AM loop antenna will provide good AM reception in
most areas. Position the loop antenna until you
hear the best reception.
AUDIO
COMPONENT VIDEO
DIGITAL OUT
DIGITAL IN
OPT. COAX.
ANTENNA
SURROUND
BACK
FRONT CENTER SURROUND
LRLR
4312
6.1CH
IN
IN OUT
TAPE CDR/MD
OUT SWOUTIN
CD C
SB
SLL
INOUTIN
R
TV DVD DSS/VCR2
RSR
L
VCR1
OUT
IN
RC-5
PRE
OUT
SR SWR
LSLC
SB
DVDTV MONI.
VIDEO
VCR1
OUTOUTIN
DSS/VCR2
OUTIN
VCR1 DSS/VCR2
DVD IN OUT
S-VIDEO
MONI.OUTTV OUTIN
C
B
/
P
B
C
R
/
P
R
C
R
/
P
R
C
R
/
P
R
C
B
/
P
B
C
B
/
P
B
DVD
YY
MONI.OUTDSS/VCR2
Y
FM
(
75
Ω
)
GND AM
MINIMUM 6 OHMS
SPEAKER SYSTEMS
AC IN
SERIAL NO.
AC OUTLETS
120V 60H
Z
SWITCHED
1A 120W MAX
UNSWITCHED
1A 120W MAX
bnzx c m
.
⁄0
⁄3 ⁄2
v
,⁄1