Filter
Top Products
17
ENGLISH
ENGLISH
1 INPUT SETUP (ASSIGNABLE DIGITAL
INPUT)
Four digital inputs can be assigned to a desired
source.
Use this menu to select the digital input jack to be
assigned to the input source.
1.
Select “INPUT SETUP” in SETUP MAIN MENU
with or cursor button, and press the OK
button.
2.
To select the input source, press or cursor
buttons.
3.
To select the digital input jack , press the or
cursor buttons.
Select “Dx-AT” for input sources, for automatic
detection of the digital input signal condition.
If there is not a digital signal present, but there
is an analog signal present, the analog signal
will be played.
Select “Dig x”, when only a digital signal will be
used.
Select “ANA” for input sources for which no
digital input jacks are used.
4.
After you complete this portion of the set up,
move the cursor to MAIN with or cursor
buttons and press the OK button.
Notes:
• The TUNER and AUX are fixed to the analog
input, and cannot be selected for any digital input.
• When a DTS-LD or DTS-CD is playing, this setup
is not available. This is to avoid noise being
generated from the analog input.
• If “Dx-AT” is selected and a DVD, compact disc
or LD is fast-forwarded during playback, decoded
signals may produce a skipping sound. In such
cases, change the setting to DIGITAL.
2 SPEAKER SETUP
After you have installed the SR5400, connected all
the components, and determined the speaker
layout, it is now time to perform the settings in the
Speaker Setup menu for the optimum sound
acoustics for your environment and speaker layout.
Before you perform the following settings, it is
important that you first determine the following
characteristics:
2-1 SPEAKERS SIZE
When setting the speaker size in the SPEAKER
SIZE sub-menu, use the guidelines given below.
LARGE:
The complete frequency range for the channel
you are setting will be output from the speaker.
SMALL:
Frequencies of the channel you are setting
lower than approx. 100 Hz will be output from
the subwoofer.
If the Subwoofer is set to “NONE” and the front
speakers are set to “Large,” then the sound will
be output from both the left and right speakers.
1.
Select “SPEAKER SETUP” in MAIN SETUP
MENU with the or cursor buttons, and press
the OK button.
2.
To select the each speaker , press the or
cursor buttons.
3.
To select the setting of each speaker size,
press the or cursor buttons.
4.
After you complete this portion of the set up,
move the cursor to “NEXT” with the or
cursor buttons and then press the OK button
to go to the next page.
SUBWOOFER:
YES:
Select when a subwoofer is connected.
NONE:
Select when a subwoofer is not connected.
1INPUTSETUP
CD : D3 -AT TV : ANA
TAPE : ANA DVD :D4 -AT
CD-R :D1-AT VCR1 :ANA
DSS : D2 -AT
MA I N EX I T
2-1 SPEAKERS SIZE
SUBWOOFER : YES
FRONT L/R : LARGE
CENTER : SMALL
SURROUND L/R : SMALL
SURR . BACK : SMALL
LPF/HPF : 100 HZ
BASS MI X : BOTH
MA I N NEXT EX I T
FRONT L/R
LARGE:
Select if the front speakers are large.
SMALL:
Select if the front speakers are small.
• If “NONE” is selected for the Subwoofer setting,
then this setting is fixed to “Large.”
CENTER
NONE:
Select if no center speaker is connected.
LARGE:
Select if the center speaker is large.
SMALL:
Select if the center speaker is small.
SURROUND L/R
NONE:
Select if no surround left and right speakers are
connected.
LARGE:
Select if the surround left and right speakers are
large.
SMALL:
Select if the surround left and right speakers are
small.
SURR. BACK
LARGE:
Select if the surround back speaker is large.
SMALL:
Select if the surround back speaker is small.
NONE:
Select if no surround back speaker is connected.
• If “None” is selected for the Surround L/R setting,
then this setting is not available.
LPF/HPF
When you use a subwoofer, you can select the
cutoff frequency for the small speakers used. Select
one of the crossover frequency levels according to
the size of the small speaker connected.
80Hz :
Select this when the bass speaker is about 12
cm (4 3/4 inches).
100Hz :
Select this when the bass speaker is about 10
cm (3 15/16 inches).
120Hz :
Select this when the bass speaker is about 8 cm
(3 3/16 inches).
Notes:
•
Use the above comments as reference when adjusting.
• If S- Direct mode , 6.1CH Input is in use, this
function does not take effect.
BASS MIX
• The bass mix setting is only valid when “LARGE”
is set for the front speakers and “YES” is set for
the subwoofer during stereo playback .
• When “BOTH” is selected, the low frequencies
will be played through the main L&R, as well as
the sub woofer.
In this playback mode, the low frequency range
expand more uniformly through the room, but
depending on the size and shape of the room,
interference may result in a decrease of the
actual volume of the low frequency range.
• By selecting “MIX”, the low frequencies will play
through the main L&R ONLY.
Note:
LFE signals during playback of Dolby Digital or
DTS, will be played through the sub woofer.