Marantz SR5001 Stereo Receiver User Manual


  Open as PDF
of 51
 
16
ENGLISH
LEARN MODE
This remote control is capable of learning and storing
codes used by other remote controls that you already
own.
For codes which are not learned, the remote control
will transmit either the Marantz preset codes from
the initial settings, or remote codes from another
manufacturer’s AV equipment which is set by the
customer.
The receiver sensor for the remote control signals is
located at the top of the remote control.
Notes:
• This remote control is capable to learn around 60
codes.
• When the batteries are getting weak , the learing
procedure is not successful.
LEARNING PROCEDURE
1.
Place the remote controller so that its infrared
signal transmitter is facing the infrared signal
receiver on the Marantz remote controller at a
distance of about 0.05 m (2 inches).
S
Y
S
T
E
M
R
E
M
O
T
E
C
O
N
T
R
O
LL
E
R
R
C
5
5
0
0
S
R
0.05 m
2.
Press and hold down the SET and MENU
buttons until LEARN indicator blinks.
123
INPUT
dts
P.DIRECT
l/
OFF
ON
AUTO
SURROUND
SLEEP
DISPLAY
LIP SYNC/
SOURCE
SET
CAT
MULTI/
ENTER
INFO
M-SPKR
MENU
3.
Select the SOURCE button to select the
SOURCE.
REMOTE CONTROLLER
RC5001SR
TAPETAPE
BASS
TREBLE
MDMD
CDRCDR
CDCD
DVDDVD
AMPAMP
AUX2AUX2
VCRVCR
TUNERTUNER
DSSDSS
TVTV
AUX1AUX1
4.
Select the button to be learned.
• LEARN indicator lights up.
123
456
T.MODE
INPUT
EX/ES
VIRTUAL
CS
dts
P.DIRECT
l/
AUTO
SURROUND
SLEEP
DISPLAY
LIP SYNC/
5.
Press and hold the button of the original remote
controller to learn until the SEND indicator
blinks twice.
• When the SEND indicator blinks once,
repeat this step.
• When the memory of the RC5001SR is
full, the LEARN and SEND indicators blink
once. If you want to learn the code, you
should erase other learned button.
6.
Repeat steps
4
and
5
to learn other buttons in
same SOURCE.
7.
Repeat steps
3
to
6
to learn other SOURCE.
8.
When you have finished programming the
remote controller, press the SET button, then
LEARN indicator stops blinking and exits from
the LEARN mode.
SEND
dts
P.DIRECT
l/
OFF
ON
SET
AUTO
SURROUND
SLEEP
DISPLAY
SOURCE
INPUT
LIP SYNC/
LEARN
Notes:
• When the SEND indicator blinks once again, the
transmitting code is unavailable for RC5001SR, or
the transmitting signal is intercepted by noise.
• If no buttons are pressed for approximately 1
minutes while in the LEARN mode, the remote
controller automatically exits from the LEARN
mode.
ERASING PROGRAMMED CODES
(RETURNING TO INITIAL SETTINGS)
Codes can be erased in three ways: by buttons,
sources, and by all memory contents.
Erasing the code by buttons
1.
Press and hold down the SET and MENU
buttons until LEARN indicator blinks.
123
INPUT
dts
P.DIRECT
l/
OFF
ON
SET
AUTO
SURROUND
SLEEP
DISPLAY
LIP SYNC/
SOURCE
CAT
MULTI/
MENU
ENTER
INFO
M-SPKR
2.
Select the SOURCE button to select the button
to be erased.
REMOTE CONTROLLER
RC5001SR
TAPETAPE
BASS
TREBLE
MDMD
CDRCDR
CDCD
DVDDVD
AMPAMP
AUX2AUX2
VCRVCR
TUNERTUNER
DSSDSS
TVTV
AUX1AUX1
3.
Press and hold down the SLEEP button and
press the learned button twice to be erased.
• SEND indicator blinks twice and the mode
returns to LEARN mode.
123
INPUT
dts
P.DIRECT
l/
OFF
ON
SET
AUTO
SURROUND
SLEEP
DISPLAY
LIP SYNC/
SOURCE
4.
To return the NORMAL mode, press the SET
button.
Erasing the code by SOURCE
1. Press and hold down the SET and MENU
buttons until LEARN indicator blinks.
123
INPUT
dts
P.DIRECT
l/
OFF
ON
SET
AUTO
SURROUND
SLEEP
DISPLAY
LIP SYNC/
SOURCE
CAT
MULTI/
ENTER
INFO
M-SPKR
MENU
2. Press and hold down the SLEEP button and
press the learned SOURCE button twice to be
erased.
• LEARN indicator lights.
TAPETAPE
AMP
BASS
TREBLE
CH
-
SEL
V
-
OFF
ATT
.
MDMD
CDRCDR
CDCD
DVDDVD
AUX2AUX2
VCRVCR
TUNERTUNER
DSSDSS
TVTV
AUX1AUX1
123
INPUT
dts
P.DIRECT
l/
OFF
ON
SET
AUTO
SURROUND
SLEEP
DISPLAY
LIP SYNC/
SOURCE
3. Press ENTER button to continue erasing.
• The SEND indicator blinks twice and the
mode returns to LEARN mode.
• To cancel the erasing operation, do not
press
ENTER
button and simply touch any
other button.
MENU
ENTER
EXIT
INFO
T.TONE
/SET UP
4. To return the NORMAL mode, press the SET
button.
Erasing the all SOURCES
1.
Press and hold down the SET and MENU
buttons until LEARN indicator blinks.
123
INPUT
dts
P.DIRECT
l/
OFF
ON
SET
AUTO
SURROUND
SLEEP
DISPLAY
LIP SYNC/
SOURCE
CAT
MULTI/
MENU
ENTER
INFO
M-SPKR
2.
Press and hold down the SLEEP button and
press POWER ON and POWER OFF button.
• LEARN indicator lights.
123
INPUT
dts
P.DIRECT
l/
OFF
ON
SET
AUTO
SURROUND
SLEEP
DISPLAY
LIP SYNC/
SOURCE
3.
Press ENTER button to continue erasing.
• The SEND indicator blinks twice and the
mode returns to LEARN mode.
• To cancel the erasing operation, do not
press
ENTER
button and simply touch any
other button.
MENU
ENTER
EXIT
INFO
T.TONE
/SET UP
4. To return the NORMAL mode, press the SET
button.
Note:
Erasing codes will return to the factory preset code,
or there will leave empty if the button has no factory
preset code.
 previous next