Filter
Top Products
32
ENGLISH
HT-EQ
Press the HT-EQ button on the front panel to turn on the HT-EQ mode.
The tonal balance of a film soundtrack will be excessively bright and
harsh when played back over audio equipment in the home. This is
because film soundtracks were designed to be played back in large
movie theater environments.
Activating the HT-EQ feature when watching a film made for movie
theaters corrects this and restores the correct tonal balance.
The HT-EQ feature can be activated only while in Dolby Pro Logic
Mode, or while decoding Dolby Digital or DTS encoded material.
6.1 CH INPUT.
The SR4300 is equipped for future expansion through the use of Multi
channel SACD multi channel player or DVD-Audio player.
This is selected, the input signals connected to the Front left, Front
right, Center, Surround left, Ssurround right and Surround back
channels of the 6.1 CH. In jacks are output directly to the front (left and
right), center, surround (left and right) and surround back speaker
systems as well as the pre-out jacks without passing through the
surround circuitry.
In addition, the signal input to the SW (subwoofer) jack is output to the
PRE OUT SW (subwoofer) jack.
When 6.1 CH. INPUT is selected, the last video input used remains
routed to the Monitor Outputs.
This permits simultaneous viewing with video sources.
1.
Select a desired Video source to decide the routed video signal to
the Monitor Outputs .
2.
Press the 6.1 CH-IN button on the front panel or on the remote to
switch the 6.1 channel input.
3.
If necessary to adjust the output level of each channel, use “6.1
Ch. INPUT LEVEL” in SETUP menu system as desired.
Adjust the speaker output levels so that you can hear the same
sound level from each speaker at the listening position. For the
front left, front right, center, surround left, surround right and
surround back speakers, the output levels can be adjusted
between –10 to +10 dB.
The subwoofer can be adjusted between –15 and +10 dB.
These adjusting result will be stored to 6.1 Ch. INPUT condition.
(see to page 24)
4.
Adjust the main volume with the MAIN VOLUME knob or the VOL
buttons on the remote.
To cancel the 6.1 Ch. INPUT setting, press the 6.1 CH-IN button on
the front panel or on the remote.
Notes:
• When the 6.1 Ch. Input is in use, you may not select a surround
mode, as the external decoder determines processing.
• In addition, there is no signal at the record outputs when the 6.1
Ch. Input is in use.
CLEAR
F/P
MODE
TUNING/PRESET
MEMORY
PHONES
SURROUND
AV SURROUND RECEIVER SR4300
STANDBY
POWER ON/STANDBY
MUTE
S-DIRECT
HT-EQ
DSS/VCR2
DVD
CDR/MD
TAPE
CD
TUNER
TV
A/D
DIMMER
6.1CH-IN
VCR1
UP
VOLUME
DOWN
HT-EQ
CLEAR
F/P
MO
D
TUNING/PRESET
MEMORY
PHONES
SURROUND
AV SURROUND RECEIVER SR4300
STANDBY
POWER ON/STANDBY
S-DIRECT
HT-EQ
DSS/VCR2
DVD
CDR/MD
TAPE
CD
TV
A/D
DIMMER
6.1CH-IN
VCR1
6.1CH-IN
2.
OFF
TREBLE
OK
CS
2
BASS
1
4
8
5
9
6
3
7
0
MENU
AUTO
DTS
DSP
6.1CH
-IN
2CH
EX/ES
M-CH
ST
A/D
SETUP/T.TONE
F.DIRECT
9
6.1CH
-IN
2.