Filter
Top Products
6
English
English
RECORDER OPERATION
Control used for operating the tape deck.
PLAYBACK
1. Set the INPUT SELECTOR switch
AA
AA
A to MD/TAPE or CD-R.
2. Play a prerecorded disc or tape on the recorder.
3. Adjust the volume with the VOLUME control
BB
BB
B.
4. Adjust the tone with the BASS and TREBLE controls
CC
CC
C.
RECORDING
The playback sound of a program source component, such as a
turntable, a tuner, or a CD player, can be recorded on disc or tape
as follows.
1. Set the INPUT SELECTOR switch
AA
AA
A to the program source
to be recorded.
2. Play the program source.
3. Operate the recorder(s) to record the playback sound on
disc(s) or tape(s).
Using REC SELECTOR switch
The REC SELECTOR switch is used when copying a recorded
disc or tape to another disc or tape, or recording a CD onto a
recordable disc or cassette tape.
1. When the switch is in the OFF position, the signal is not output
at the REC OUT jacks.
It is not necessary to output the signal at the REC OUT jacks
when the signal is not recorded onto disc or tape.
By setting the switch to OFF, the signal path inside the unit can
be shortened and crosstalk, etc., can be reduced.
2. In the SOURCE position, the signal selected with the INPUT
SELECTOR switch can be recorded onto disc/tape.
3. In the COPY positions, the MD/TAPE signal can be recorded
onto CD-R or vice versa.
4. In the COPY position, the program source selected with the
INPUT SELECTOR switch can be monitored through the
speakers.
OPERATION PROCEDURES
Operate each equipment to start play.
TO PLAY AN ANALOG DISC
1. Set the INPUT SELECTOR switch q to PHONO.
2. Play a disc on the turntable.
3. Adjust the volume with the VOLUME control w and adjust the
tone with the BASS and TREBLE controls e.
NOTES:
¡ Set the VOLUME control to the minimum position before
placing the stylus on the disc or before replacing the cartridge.
¡ Do not apply shock or vibration to the turntable during play, as
this may cause the stylus to jump and the analog disk to be
damaged.
¡ If the turntable is installed too close to the speakers, the
volume may not be able to be increased to a high level due to
howling.
¡ Do not switch the power OFF while the stylus is on the disc
surface.
TO LISTEN TO FM/AM BROADCASTS
1. Set the INPUT SELECTOR switch q to TUNER.
2. Tune in the desired station on the tuner.
3. Adjust the volume with the VOLUME control w and adjust the
tone with the BASS and TREBLE controls e.
TO PLAY A DVD OR COMPACT DISC
1. Set the INPUT SELECTOR switch q to CD.
2. Play a CD on the CD player.
3. Adjust the volume with the VOLUME control w and adjust the
tone with the BASS and TREBLE controls e.
TO PLAY A DVD OR COMPONENT CONNECTED TO AUX
JACKS
The component connected to the AUX jacks on the rear panel
can be played as follows.
1. Set the INPUT SELECTOR switch q to AUX.
2. Play the component connected to the selected input.
3. Adjust the volume with the VOLUME control w and adjust the
tone with the BASS and TREBLE controls e.
INTEGRATED AMPLIFIER PM4200
PHONO CD TUNER AUX/DVD CD-R MD/TAPE
MUTETONE DEFEAT
MIN
VOLUMEINPUT SELECTOR
PHONESPOWER ON/OFF STANDBY
ON
OFF
ON
OFF
LOUDNESS
ON
OFF
AUX/DVDCOPY
TUNER
CD-R→
MD/TAPE
CD
MD/TAPE
→CD-R
PHONOSOURCE
REC SELECTOR
OFF
BASS TREBLE
1
2SPEAKERS
– + – +
MAX BALANCE
LR
INTEGRATED AMPLIFIER PM4200
PHONO CD TUNER AUX/DVD CD-R MD/TAPE
MUTETONE DEFEAT
MIN
VOLUMEINPUT SELECTOR
PHONESPOWER ON/OFF STANDBY
ON
OFF
ON
OFF
LOUDNESS
ON
OFF
AUX/DVDCOPY
TUNER
CD-R→
MD/TAPE
CD
MD/TAPE
→CD-R
PHONOSOURCE
REC SELECTOR
OFF
BASS TREBLE
1
2SPEAKERS
– + – +
MAX BALANCE
LR
REC SELECTOR
AUX/DVDCOPY
TUNER
CD-R→
MD/TAPE
CD
MD/TAPE
→CD-R
PHONOSOURCE
REC SELECTOR
OFF