Kenwood KRF-V4530D Stereo Receiver User Manual


 
16
Preparations
Preparing for surround sound
Input level adjustment (analog sources only)
If the input level of an analog source signal is too high, adjust the input
level.
1
• You can store a separate input level for each input source. If the
MONITOR function is on, you can store an input level for when
MONITOR is on independently of the input levels for the input
sources.
2
3
• The adjustment mode is displayed for approximately eight seconds.
•The input level may be adjusted to any one of three settings: 0,
-3, and -6. (The initial setting is 0.)
4
Preparing for playback
Normal playback
Some preparatory steps are needed before starting playback.
Turning on the receiver
1
2
Selecting MD/TAPE
Select the source name corresponding to the component connected to
the MD/TAPE jacks. The initial factory setting is “ ”. To change the
source name associated with the MD/TAPE jacks to “ ,” follow the
steps below:
1
2
• The source indication changes to “ ”.
• To return to the original indication, repeat the above procedure.
• You also will need to change the name input to the remote control to
”. 1
Sound from the speakers connected to the SPEAKERS A
terminals on the rear panel.
Sound from the speakers connected to the SPEAKERS B
terminals on the rear panel.
Sound from both the speakers connected to the SPEAKERS
A and B terminals on the rear panel.
No sound from the speakers. Use this setting when listening
with headphones for stereo sound and virtual surround in all
playback modes.
Selecting the input mode
If you have selected a component connected to the
or (KRF-V7030D only) jacks, make sure that the input mode
setting is correct for the type of audio signal to be used. 0
5
Display when all speakers have been selected.
• The speakers you selected appear on the display. Confirm that all
the speakers have been correctly selected.
4
The speaker indicator to be adjusted blinks.
Indication in feet Indication in meters
1
Distance to front speakers: ____ feet (meters)
Distance to center speaker: ____ feet (meters)
Distance to surround speakers: ____ feet (meters)
2
• The allowable setting range is 1 to 30 feet (0.3 to 9.0 m), adjustable
in 1 foot (0.3 m) increments.
3
4 2 3
Operations
Input the distance to the speakers.
LFE
C
S
RSLS
TI.VOLB
CLIP MUTE
RDS EON PTY
TP TA NEWS
L
SP A
R
SW
SW
STEREO
FM
AM
MHz
kHz
PRO LOGIC
3
DOWN MIX
DIGITAL
S.DIRECT
MONITOR
DSP
MEMO
ST.
TUNED
AUTO SOUND
AUTO
LFE
C
S
RSLS
TI.VOLB
CLIP MUTE
RDS EON PTY
TP TA NEWS
L
SP A
R
SW
STEREO
FM
AM
MHz
kHz
PRO LOGIC
3
DOWN MIX
DIGITAL
S.DIRECT
MONITOR
DSP
MEMO
ST.
TUNED
AUTO SOUND
AUTO
LFE
C
S
RSLS
TI.VOLB
CLIP MUTE
RDS EON PTY
TP TA NEWS
L
SP A
R
AUTO
INPUT MODE
POWER
ON/STANDBY
INPUT SELECTOR
SPEAKERS A/B
LFE
C
S
RSLS
TI.VOL
CLIP MUTE
RDS EON PTY
TP TA NEWS
L
SP A
R
SW
B
Selecting the speaker system (except for KRF-V5030D/
V4530D)
LFE
C
S
RSLS
TI.VOL
CLIP MUTE
RDS EON PTY
TP TA NEWS
L
SP A
R
SW
B
The speaker indicator lights.
KRF-V5030D/V4530D
KRF-V7030D/V6030D
The indicator for the speakers
you want to use should be lit.
•Activating a surround mode or selecting “DVD/6ch” as the input
source causes speaker system A to be selected automatically.