Kenwood VR-9060 Stereo System User Manual


 
17
EN
Preparing for surround sound
Speaker settings
To enable you to obtain optimum enjoyment from the receiver’s listening
modes, make sure to complete the speaker settings (Subwoofer, Front,
Center, Surround and Surround Back Speakers) as described below.
SETUP MULTI CONTRO
L
RECEIVER ON
SETUP
MULTI %/,
@/#
(POWER
ON/STANDBY)
RCV MODE
SOUND
SOUND
1
Turn on the power to this receiver by pressing the
(POWER
ON/STANDBY) key or RECEIVER ON key.
2
For the remote control unit, press the RCV MODE key to
switch to receiver mode.
3
Press the SETUP key to enter the SETUP mode.
Use the
55
55
5
/
keys or MULTI
@
/
#
keys
for the following
displays.
1 SP SETUP
2 CROSSOVER
3 TEST TONE
4 SP DISTANCE
5 LFE LEVEL
6 DISP MODE
7 EXIT
The flow of the SETUP is as follows:
Display Selector
Display Listen
LFE
LEVEL
DISP
MODE
EXIT
Front Left
Center
Front Right
Surround Right
Surround Back Right
Surround Back Left
Surround Left
Subwoofer
SP
DISTANCE
FREQ:40Hz
FREQ:60Hz
FREQ:80Hz
FREQ:100Hz
FREQ:120Hz
FREQ:150Hz
L
C
R
SR
SBR
SL
SBL
SW
L
C
R
SR
SBR
SBL
SL
SW
SP
SETUP
Subwoofer
Front
Center
Surround
Surround
Back
Subwoofer
Re-mix
TEST
TONE
T. TONE
MANUAL
T. TONE
AUTO
CROSSOVER
4
Select a speaker system.
1 Select the SP SETUP and press the SETUP key again so that
the subwoofer setting indication “SUBW ON” appears.
L
SL SB SR
CR
SP MUTE
AB CLIP
SW
LFE
STEREO
2 Use the MULTI CONTROL knob or MULTI %/ keys to select
the appropriate subwoofer setting.
1 SUBW ON : Subwoofer setting mode to the receiver is ON.
2 SUBW OFF : Subwoofer setting mode to the receiver is
OFF.
•The initial setting is “SUBW ON”.
When the setting “SUBW OFF” is selected, the Front Speakers
are automatically set to “FRNT LARGE” and the procedure skips
to step 6.
When Subwoofer output sound is required, select “FRNT NORMAL”,
or select both “FRNT LARGE” and “SW RE-MIX ON”.
After setting SW (Subwoofer) from OFF to ON, SB/SW AMP setup
display will appear to enable you to re-select either SW or SB from
the Surround Back Speaker or Subwoofer terminal.
3 Press the 5 key or MULTI # key to accept the setting.
The front speakers setting indication “FRNT” appears.
L
SL S SB SR
CR
SP MUTE
AB CLIP
SW
LFE
STEREO
4 Use the MULTI CONTROL knob or MULTI %/ keys to select
the appropriate front speakers setting.
1 FRNT NORMAL : Average size Front Speakers are connected
to the receiver.
2 FRNT LARGE : Large size Front Speakers are connected
to the receiver.
5 Press the
55
55
5
key or MULTI # key to accept the setting.
The Center Speaker setting indication “CNTR” appears.
6 Use the MULTI CONTROL knob or MULTI %/ keys to select
the appropriate Center Speaker setting.
If you selected “FRNT LARGE” as the Front Speakers setting,
1 CNTR NORMAL : An average size Center Speaker is con-
nected to the receiver.
2 CNTR LARGE : A large size Center Speaker is connected
to the receiver.
3 CNTR OFF : Center Speaker setting mode to the re-
ceiver is OFF.
If you selected “FRNT NORMAL” as the Front Speakers
setting,
1 CNTR NORMAL : An average size Center Speaker is
connected to the receiver.
2 CNTR OFF : Center Speaker setting mode to the
receiver is OFF.
7 Press the 5 key or MULTI # key again to accept the setting.
The Surround Speaker setting indication “SURR” appears.
Continued to next page.
05.2.8, 6:53 PM17