Filter
Top Products
21
Preparations
5 Setup is complete when the input indication reappears.
Display when all speakers have been selected.
• The speakers you have selected should appear on the display.
Confirm that all the speakers have been correctly selected.
4
The speaker indicator to be adjusted blinks.
Indication in feet Indication in meters
1 Measure the distance from the listening position to each of
the speakers.
Jot down the distance to each of the speakers.
Distance to front speakers: ____ feet (meters)
Distance to center speaker: ____ feet (meters)
Distance to surround speakers: ____ feet (meters)
2 Use the MULTI CONTROL knob or 5/∞ keys to select the
distance to the front speakers.
• The allowable setting range is 1 to 30 feet (0.3 to 9.0 m), adjustable
in 1 foot (0.3 m) increments.
3 Press the SET UP or display operation 2 [Next] key.
4 Repeat steps 2 and 3 to input the distance for each of the
speakers.
Input the distance to the speakers.
LFE
C
S
RSLS
TI.VOLB
CLIP MUTE
RDS EON PTY
TP TA NEWS
L
SP A
R
SW
•If you change the volume level settings for the speakers while
listening to music, the settings referred to on this page are also
changed º
• If the speaker setting selects are OFF, the speaker level settings
are reset.
2 Press the SET UP or display operation 2 [Next] key.
• The test tone is turned off. The receiver enters the mode for inputting
the distance to the speakers.
Input level adjustment (analog sources only)
MEMO
ST.
TUNED
FM
AM
MHz
kHz
PRO LOGIC
3
DOWN MIX
DIGITAL
S.DIRECT
MONITOR
DSP
AUTO SOUND
AUTO
CLIP
LFE SW
S RSLS
B
MUTE
TI.VOL
RDS EON PTY
TP TA NEWS
STEREO
C
SP A
L R
If the input level of an analog source signal is too high, the CLIP indicator
will blink. Adjust the input level.
1 Use the INPUT SELECTOR knob to select the source which
input level you want to adjust.
•You can store a separate input level for each input source. If the
MONITOR function is ON, you can store an input level for when
MONITOR is on independently of the input levels for the input
sources.
2 Press the SOUND key repeatedly until the “INPUT”
indication appears.
3 Use the MULTI CONTROL knob or 5/∞ keys to adjust the
input level.
• The adjustment mode is displayed for approximately eight seconds.
•The input level may be adjusted to any one of three settings: 0dB,
-3dB, and -6dB. (The initial setting is 0dB.)
4 Press the SOUND key again to return to the input indication.
SW
FM
AM
MHz
kHz
PRO LOGIC
3
DOWN MIX
DIGITAL
S.DIRECT
MONITOR
DSP
MEMO
ST.
TUNED
AUTO SOUND
AUTO
LFE
C
S
RSLS
TI.VOLB
CLIP MUTE
RDS EON PTY
TP TA NEWS
L
SP A
R
STEREO
SW
RDS
TP
CLIP
The channel indication blinks while the test tone is being output.
3
From your usual listening position, adjust the volume levels. The volume
levels from each speaker should be the same.
1 Use the MULTI CONTROL knob or 5/∞ keys to adjust the
volume of the test tone output from the speaker channel to be
adjusted.
The test tone is heard from the speakers in the following
sequence for 2 seconds each:
STEREO
R
FM
AM
MHz
kHz
PRO LOGIC
3
DOWN MIX
DIGITAL
S.DIRECT
MONITOR
DSP
MEMO
ST.
TUNED
AUTO SOUND
AUTO
LFE
C
S
RSLS
TI.VOLB
CLIP MUTE
RDS EON PTY
TP TA NEWS
L
SP A
= L = C = R = SR = SL = SW
Adjust the speaker volume.
Preparing for surround sound
*509/19-21/EN 3/15/01, 2:03 PM21